FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-F3190 2021ASTM F3190-21Active Standard: Standard Practice for Heat Fusion Equipment (HFE) Operator Qualification on Polyethylene (PE) and Polyamide (PA) Pipe and FittingsASTM F3190Scope 1.1 This practice describes criteria for the training, assessment and qualification of heat fusion equipment (HFE) operators in, but not limited to, a field environment in order to establish and maintain competency in the joining of Polyethylene (PE) and Polyamide (PA) piping systems. 1.2 This HFE operator training and qualification is applicable to heat fusion joining of PE pipe and fittings to other PE pipe and fittings of related polymer chemistry specified in the heat fusion procedures or standards used. It is also applicable to heat fusion joining of PA pipe and fittings to other PA pipe and fittings of the same polymer chemistry specified in the heat fusion procedures or standards used. The heat fusion between PE pipe and fittings to PA pipe and fittings is NOT allowed. 1.3 The HFE operator training and qualification shall be for butt fusion for either PE or PA piping products, using the specific brand and size range of fusion machine to be used by the HFE operator and the heat fusion procedures or standards specified. If the HFE operator trainee requests, the training shall also include saddle and/or socket fusion of PE pipe and fittings of related polymer chemistry specified in the heat fusion procedures or standards used. This standard does not include training on the electro-fusion of these piping products. 1.4 The HFE operator qualification shall be for one specific manufacturer’s fusion machine or a size range of that manufacturer’s hydraulic fusion machines or equipment that all operate in the same manner with the same hydraulic design and controls and the same heater and facer design. For smaller pipe sizes (6 in. and smaller), the qualification can be on a specific fusion machine or a combination of butt, saddle and/or socket fusion machines or equipment. 1.5 The HFE operator qualification shall be on specific heat fusion procedures or standards specified for PE and PA pipes. For PE pipe and fittings, this shall include Practice F2620 or other company or pipe manufacturer’s procedures, or a combination thereof. For PA-11 pipe and fittings, this shall include Plastics Pipe Institute (PPI) Technical Report TR-45 or other company or pipe manufacturer’s procedures. For PA-12 pipe and fittings, this shall include Practice F3372 or other company or pipe manufacturer’s procedures, or a combination thereof. For other PA pipe materials, use other company or pipe manufacturer’s procedures. 1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords heat fusion equipment operator qualification; heat fusion equipment operator training organization; ICS Code ICS Number Code 23.040.20 (Plastic pipes) DOI: 10.1520/F3190-21 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|