ASTM Standard
|
Designation
|
Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
|
D2239
|
Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
|
D2609
|
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
|
D2683
|
Standard Specification for Polyethylene (PE) Plastic Tubing
|
D2737
|
Standard Practice for Underground Installation of Thermoplastic Pressure Piping
|
D2774
|
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
|
D3261
|
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
|
D3035
|
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
|
F714
|
Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
|
F1055
|
Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
|
F1056
|
Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
|
F1290
|
Standard Specification for Deformed Polyethylene (PE) Liner
|
F1533
|
Standard Guide for Construction Procedures for Buried Plastic Pipe
|
F1668
|
Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure
|
F2164
|
Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
|
F2206
|
Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
|
F2620
|
Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
|
F2634
|
Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Gaseous Testing Media Under Pressure (Pneumatic Leak Testing)
|
F2786
|
Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes ¾ in. to 65 in.
|
F2880
|
Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods
|
F2928
|
Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
|
F3034
|
Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)
|
F3123
|
Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings
|
F3124
|
Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint
|
F3183
|
Standard Practice for Heat Fusion Equipment (HFE) Operator Qualification on Polyethylene (PE) and Polyamide (PA) Pipe and Fittings
|
F3190
|
AWWA Standards
|
|
Standards Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) Through 3 in. (76 mm), for Water Service
|
C901
|
Polyethylene (PE) Pressure Pipe and Fittings, 4 In. Through 65 In. (100 mm Through 1,650 mm), for Waterworks
|
C906
|
CSA Standards
|
|
Standards Definitions, general requirements, and methods of testing for thermoplastic pressure piping
|
B137.0
|
Polyethylene (PE) pipe, tubing, and fittings for cold water pressure services
|
B137.1
|