Search book title
Enter keywords for book title search
Search book content
Enter keywords for book content search
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(326)
ACI
(573)
AISC
(44)
ASA
(234)
ASCE
(969)
ASHRAE
(652)
ASME
(2114)
ASSE
(64)
ASTM
(92448)
AWC
(54)
AWWA
(541)
BHMA
(117)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(93277)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(351)
ICC
(300)
IEEE
(6217)
IES
(240)
ISEA
(16)
Joint Commission
(177)
Joint Commission Int.
(1)
NETA
(5)
NFPA
(1635)
TCNA
(16)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(26)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(31)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    BS EN 60695-11-10:2013 Fire hazard testing - Test flames. 50 W horizontal and vertical flame test methods
    Edition: 2014
    $418.55
    / user per year

Description of BS EN 60695-11-10:2013 2014

This part of IEC 60695 specifies small-scale laboratory test procedures intended to compare the burning behaviour of different materials used in electrotechnical products when vertically or horizontally oriented test bar specimens are exposed to a small flame ignition source with a nominal thermal power of 50 W. These test methods determine either the linear burning rate or the self-extinguishing properties of materials.

These test methods are applicable to solid and cellular materials that have an apparent density of more than 250 kg/m 3, determined in accordance with ISO 845 .

Two test methods are described. Method A is a horizontal burning test and is intended to determine the linear burning rate of materials under specific test conditions. Method B is a vertical burning test and is intended to determine whether materials self-extinguish under specific test conditions.

NOTE 1

ISO 9772 [8] 1 describes a test method for the determination of the burning characteristics to be used for materials with an apparent density of 250 kg/m 3 or less. ISO 9773 describes a test method for the determination of the burning behaviour to be used for materials that due to their thinness, either distort and/or are burned up to the holding clamp using Method B of this standard.

The test methods described provide classifications (see 8.4 and 9.4), which may be used for quality assurance, the pre-selection of component materials of products, or to verify the required minimum flammability classification of materials used in end products.

NOTE 2

Guidance on pre-selection is given in IEC 60695‑1‑30 .

This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51 .

One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.



Standard NumberBS EN 60695-11-10:2013
TitleFire hazard testing - Test flames. 50 W horizontal and vertical flame test methods
StatusDefinitive
Publication Date2014-11-30
ReplacesBS EN 60695-11-10:1999
Identical National Standard OfIEC 60695-11-10:2013/COR1:2014
CorrectsBS EN 60695-11-10:2013
DescriptorsClassification systems, Combustion test methods, Rated power, Flammability, Plastics, Flames, Electronic equipment and components, Burning rate, Vertical, Electrical components, Horizontal, Small, Density, Non-metals, Electrical equipment, Test specimens, Solids, Cellular materials, Fire tests, Polymers, Fire-test classifications, Surface spread of flame, Thermal output, Specimen preparation, Precision, Laboratory testing, Test equipment, Burners, Flame propagation, Ignitability
ICS13.220.40 Ignitability and burning behaviour of materials and products, 29.020 Electrical engineering in general
CommitteeGEL/89
ISBN978 0 580 88551 8
PublisherBSI
Pages40

About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.
GROUPS
X