FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-G163 2010ASTM G163 - 10Standard Guide for Digital Data Acquisition in Wear and Friction MeasurementsActive Standard ASTM G163 | Developed by Subcommittee: G02.20 Book of Standards Volume: 03.02 ASTM G163Significance and Use This guide illustrates the steps and considerations involved with digital data acquisition. While analog recording of wear and friction data has been in the past, digital data acquisition and storage is used extensively. It is important that DAQ users understand how data is collected and stored and how data manipulation may affect raw data integrity. Multi-station wear and friction testing is increasing in use, and because of the increased volume of data in such approaches, the use of digital data acquisition facilitates such testing. The same hardware and software used for the initial analog data conversion to digital form can often also be used for initial data processing, for example, multiple-point averaging. This can conveniently lead to computer-based storage of processed data in digital form. However, where possible, the storage of unfiltered (software filters) and unmanipulated data will allow reevaluation of original data should calibration coefficients need to be adjusted. Databases are frequently constructed in computerized format (see Guide G118 ) in order to hold large amounts of wear and friction data from laboratory test programs. 1. Scope 1.1 This guide covers the providing of general guidance in applying hardware and software to digitally acquire wear and friction data in laboratory test systems. It points out important considerations in such data acquisition. It does not make specific recommendations or discuss specific details regarding commercial hardware or software. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards G40 Terminology Relating to Wear and Erosion G77 Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test G83 Test Method for Wear Testing with a Crossed-Cylinder Apparatus G99 Test Method for Wear Testing with a Pin-on-Disk Apparatus G115 Guide for Measuring and Reporting Friction Coefficients G118 Guide for Recommended Format of Wear Test Data Suitable for Databases Keywords data acquisition; database; digital data; friction; hardware; software; tribology; wear; Digital data acquisition; Friction/frictional properties--metallic materials; Hardware; Data analysis--metals/alloys; Software; Tribology; Wear testing--metallic materials; ICS Code ICS Number Code 19.060 (Mechanical testing) DOI: 10.1520/G0163-10 ASTM International is a member of CrossRef. ASTM G163The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|