1. Scope

1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications.

1.2 Unless otherwise specified, nuts used on these bolts, cap screws, and studs shall conform to the requirements of Specification F467M. Nuts shall be of the same alloy group as the fastener on which they are used, and shall have a specified minimum proof stress equal to or greater than the specified minimum tensile strength stress of the fastener on which they are used.

Note 1This specification is the metric companion of Specification F468.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B154 Test Method for Mercurous Nitrate Test for Copper Alloys

B193 Test Method for Resistivity of Electrical Conductor Materials

B211M Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric)

B565 Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods

B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod

D3951 Practice for Commercial Packaging

E8M Test Methods for Tension Testing of Metallic Materials [Metric]

E18 Test Methods for Rockwell Hardness of Metallic Materials

E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys

E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry

E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes

E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys

E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys

E92 Test Method for Vickers Hardness of Metallic Materials

E101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique

E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys

E165 Practice for Liquid Penetrant Examination for General Industry

E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique

E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys

E478 Test Methods for Chemical Analysis of Copper Alloys

E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique

F467M Specification for Nonferrous Nuts for General Use (Metric)

F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

Keywords

bolts; cap screws; general use; nonferrous; studs ; Aluminum alloys--specifications; Copper; Copper alloy--specifications; Fasteners (metal)--specifications; Naval brass; Nickel alloy bolting materials--specifications; Nickel-copper alloy--specifications; Nickel-copper-aluminum alloys; Nickel-molybdenum alloys--specifications; Nickel-molybdenum-chromium alloys--specifications; Nonferrous bolting materials; Palladium (titanium plus palladium)--specifications; Titanium plus palladium--specifications; Titanium (Ti)/alloys--specifications; UNS N04400 (Ni-Cu alloy, Monel 400); UNS N04405 (Ni-Cu alloy solution strengthened (Monel R405)); UNS N05500 (Ni-Cu alloy, Monel K500); UNS N10001 (Ni-Mo alloy, Hastelloy B); UNS N10002 (Ni-Mo alloy, Hastelloy C); UNS N10665 (Ni-Mo alloy, Hastelloy B-2); UNS R50250 (Ti, unalloyed); UNS R50400 (Ti, unalloyed); UNS R50550 (Ti, unalloyed); UNS R50700 (Ti, unalloyed); Yellow brass

ICS Code

ICS Number Code 21.060.10 (Bolts, screws, studs)

DOI: 10.1520/F0468M-98

ASTM International is a member of CrossRef.