|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-F2869 2016ASTM F2869-10-Reapproved2016Active Standard: Standard Practice for Radial Light Truck Tires to Establish Equivalent Test Severity Between a 1.707-m (67.23-in.) Diameter Rotating Roadwheel and a Flat SurfaceASTM F2869Scope 1.1 This practice describes the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for radial pneumatic light truck (LT) tires. 1.1.1 Tire operational severity, as defined as the running or operational temperature for certain specified internal tire locations, is not the same for these two test conditions. It is typically higher for the laboratory roadwheel at equal load, speed and inflation pressure conditions due to the curvature effect. 1.1.2 The practice applies to specific operating conditions of light truck tires up through load range E for such tires used on vehicles having a gross vehicle weight rating (GVWR) ≤4536 kg (10000 lb). 1.1.3 The specific operating conditions under which the procedures of the practice are valid and useful are completely outlined in Section 6, (Limitations) of this standard. 1.1.4 It is important to note that this standard is composed of two distinct formats: 1.1.4.1 The usual text format as published in this volume of the Book of Standards (Vol. 09.02). 1.1.4.2 A special interactive electronic format that uses a special software tool, designated as prediction profilers or profilers. This special profiler may be used to determine laboratory test conditions that provide equivalent tire internal temperatures for the belt edge region for the two operational conditions, that is, the curved laboratory roadwheel and flat highway test surfaces. 1.2 The prediction profilers are based on empirically developed linear regression models obtained from the analysis of a large database that was obtained from a comprehensive experimental test program for roadwheel and flat surface testing of typical radial light truck (LT) tires. See Section 7 and the research report2 for more details. 1.2.1 For users viewing the standard on CD-ROM or PDF, with an active and working internet connection, the profilers can be accessed on the ASTM website by clicking on the links in 7.5 and 7.6. 1.2.2 For users viewing the standard in a printed format, the profilers can be accessed by entering the links to the ASTM website in 7.5 and 7.6 into their internet browsers. 1.3 For this standard, SI units shall be used, except where indicated. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords curved to flat surface; endurance; equivalency; flat to curved surface; high speed temperature; LT metric; highway equivalent; radial light truck tire; roadwheel; roadwheel testing; test severity; tire; tire temperature;  67.23-in.;  1.707-m; ICS Code ICS Number Code 83.160.10 (Road vehicle tyres) DOI: 10.1520/F2869-10R16 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|