FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-F2818 2010ASTM F2818 - 10Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and TubingActive Standard ASTM F2818 | Developed by Subcommittee: F17.60 Book of Standards Volume: 08.04 ASTM F2818Abstract This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications. Requirements cover workmanship, pipe and tubing dimensions and tolerances, chemical resistance, sustained pressure, elevated temperature, thermal stability, slow crack growth resistance, minimum hydrostatic burst pressure/apparent tensile strength (quick burst), apparent tensile strength at yield, squeeze-off, thermal stability, slow crack growth resistance, and joints. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications. 1.2 The text of this specification references notes and footnotes provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents D618 Practice for Conditioning Plastics for Testing D638 Test Method for Tensile Properties of Plastics D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement D1505 Test Method for Density of Plastics by the Density-Gradient Technique D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings D1600 Terminology for Abbreviated Terms Relating to Plastics D1898 Practice for Sampling of Plastics D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings D2290 Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings D2765 Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials D4883 Test Method for Density of Polyethylene by the Ultrasound Technique F412 Terminology Relating to Plastic Piping Systems F1051 Test Method for Comparing Multistrike Film Ribbons F1473 Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins F1563 Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing Other Standards CFRPart192 Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety StandardsKeywords Gas; gas distribution; PEX pipe; PEX Tubing; plastic piping; thermoplastic; ICS Code ICS Number Code 23.040.20 (Plastic pipes) DOI: 10.1520/F2818-10 ASTM International is a member of CrossRef. ASTM F2818The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|