FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F1319 2011ASTM F1319 - 94(2011)Standard Test Method for Determination of Abrasion and Smudge Resistance of Images Produced from Business Copy Products (Crockmeter Method)Active Standard ASTM F1319 | Developed by Subcommittee: F05.04 Book of Standards Volume: 15.09 ASTM F1319Significance and Use 5.1 The degree of image transferred by rubbing (crock) from a copy or printed image can be affected by various factors including the type of machine, the condition of the machine, supplies employed, time since imaging (ribbons) and environmental conditions. As many as possible of these variables should be controlled during the test. A control sample with known characteristics, if available, should be run along with the test samples. 5.2 The test is designed to simulate the type of damage resulting from paper rubbing against the printed image. 5.3 The test method can be used for control of product quality as well as a research and development tool. 5.4 The method is adaptable to images produced from most types of impact and non-impact printers and copiers. 5.5 Two different printers employing the same technology may yield prints with variations in optical densities. It may be possible to remove more toner or ink from the darker image yet the performance of the smudged image may be satisfactory. An optional evaluation procedure is available whereby the functional properties of the smudged or abraded image is examined if this is of primary concern. 1. Scope 1.1 This test method describes a procedure for determining the amount of image transferred onto the surface of a white cloth by rubbing. 1.2 The test method can be employed to evaluate the abrasion and smudge resistance of business imaging products produced by impact printers, thermal transfer printers, and non-impact printers or copiers. 1.3 The test method can be used to evaluate the amount of material removed from the sample (smudge or crock). Testing focuses on determining the amount of material deposited on the crockmeter cloth or redeposited in a new location on the sample. The test method can also be employed to measure performance characteristics for a product. The user should select test equipment which is appropriate for measuring the abrasion to the samples. Samples are tested before and after rubbing and comparisons of results made. In this test method product performance evaluations are optional. 1.4 Other test methods employing the Sutherland rub tester, Taber Abrader and Gavarti GA-C.A.T. can be employed to evaluate the smudge and abrasion characteristics. Results by these units are not necessarily equivalent to those obtained with the Crockmeter. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards F335 Terminology Relating to Electrostatic Imaging F360 Practice for Image Evaluation of Electrostatic Business Copies F497 Practice for Use of the Electric and Electronic Typewriter as a Test Instrument F1174 Practice for Using a Personal Computer Printer as a Test Instrument F1175 Practice for Using the Computer Impact Print-Out Unit as a Test Instrument for Manifold Comparison ANSI Standards PH2.18 Density Measurements-Special ConditionsKeywords abrasion resistance; copying; Crockmeter; impact printers; inked ribbons; MICR; non-impact printers; OCR; smudge resistance; thermal transfer ribbons; toner images ; ICS Code ICS Number Code 37.100.10 (Reproduction equipment) DOI: 10.1520/F1319-94R11 ASTM International is a member of CrossRef. ASTM F1319This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|