|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E3035 2015ASTM E3035-15Historical Standard: Standard Classification for Facility Asset Component Tracking System (FACTS)ASTM E3035Scope 1.1 This standard (FACTS) establishes a classification of building and sitework elements and components, and their associated functions, attributes, and products. Elements, as defined here, are major assemblies and components common to buildings and sitework. Elements usually perform given functions, regardless of the design specification, construction method, or materials used. The attribute classification will lead to more effective management of the operation, maintenance, and life cycle cost of the asset. 1.2 The classification: 1.2.1 Incorporates Levels 1, 2, and 3 from Classification E1557: 1.2.1.1 Major Group Element (Classification E1557 Level 1). 1.2.1.2 Group Element (Classification E1557 Level 2). 1.2.1.3 Element (Classification E1557 Level 3). 1.2.2 Establishes sub-elements at Levels 4 and beyond: 1.2.2.1 Because the main objective is content and not specifically rigid structure, levels beyond those established in Classification E1557 are not balanced. 1.2.2.2 Products and characteristics are introduced at varying levels, depending on the appropriate element and elemental function. 1.2.2.3 Functional elements are aligned with products and product characteristics. 1.2.3 Incorporates the noun-adjective-attribute relationship between elements, elemental function and the associated products and characteristics. 1.2.4 This approach identifies specific products that will support the element at its functional level. However, the classification permits the introduction of additional products necessitated due to higher order requirements, such as but not limited to: (1) Asset type (2) Asset function (3) Asset conditions (4) Building code requirements 1.3 The classification seeks to define a larger universe of attributes, products, and characteristics that may define its functional use and life cycle cost. 1.4 The classification also provides a logical database structure for the implementation of related Real Property Management applications and business processes such as: (1) Building Information Modeling (BIM) Technologies (2) Smart Building Technologies (3) Sustainability (4) Computerized Maintenance Management Systems (CMMS) (5) Facility Asset Management Systems (6) Property Condition Assessment (7) Real Property Development (8) Project Management Systems (9) Cost Planning, Estimating, and Control Procedures 1.5 Use of the classification provides a consistent means for analysis, evaluation, monitoring, and reporting during the life of the asset, from planning through design, construction, operations, maintenance, rehabilitation, and disposal. 1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords adjective; asset management; attribute; BIM; CMMS; condition assessment; cost estimating; cost planning; element; function; inventory; life cycle cost; maintenance; non-recurring; noun; present value; product; recurring; risk management; sustainability; value engineering; verb; ICS Code ICS Number Code 03.060 (Finances. Banking. Monetary systems. Insurance) DOI: 10.1520/E3035-15 The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|