|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E2346/E2346M 2014ASTM E2346/E2346M-14Historical Standard: Standard Guide for Sensory Evaluation of Household Hard Surface-Cleaning Products with Emphasis on Spray TriggersASTM E2346/E2346MScope 1.1 This guide presents guidelines specific to the sensory evaluation of trigger hard surface cleaners. It covers the procedure for preparing a nonporous surface with the intent to measure one or all of the various aspects of a trigger product: package, application, performance, and after-use properties, with focus on visual, tactile, fragrance, performance, and package ergonomics. It is applicable for use with assessors, highly trained assessors, and consumers. 1.2 This guide for preparing nonporous hard surfaces is intended to focus on surface preparation and evaluation, not on panel selection, training, or development. 1.3 The reader should be aware that good sensory practices are required when preparing the surfaces, and in developing and training the assessors. 1.4 The researcher is responsible for identifying the most appropriate test design and using the appropriate statistical tool to address that experimental design. 1.5 Since this guide's intended use is to provide direction on the presentation and measurement of the different aspects of spray trigger hard surface cleaners, this guide may not accurately represent all possible soils and surfaces where spray trigger hard surface cleaners may be used. 1.6 This guide provides suggested procedures and is not meant to exclude alternate procedures that may be effectively used to provide the same results. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values are stated in only SI units when inch-pound units are not used in practice. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory requirements prior to use. Keywords ceramic; glass; hard surfaces; nonporous; sheet acrylic; Spangler soil; spray trigger cleaner ICS Code ICS Number Code 71.100.99 (Other products of the chemical industry) DOI: 10.1520/E2346_E2346M-14 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|