FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E1602 2010ASTM E1602 - 03(2010)e1Standard Guide for Construction of Solid Fuel Burning Masonry HeatersActive Standard ASTM E1602 | Developed by Subcommittee: E06.54 Book of Standards Volume: 04.11 ASTM E1602Significance and Use This guide can be used by code officials, architects, and other interested parties to evaluate the design and construction of masonry heaters. It is not restricted to a specific method of construction, nor does it provide all specific details of construction of a masonry heater. This guide does provide the principles to be followed for the safe construction of masonry heaters. This guide is not intended as a complete set of directions for construction of masonry heaters. Construction of masonry heaters is complex, and in order to ensure their safety and performance, construction shall be done by or under the supervision of a skilled and experienced masonry heater builder. 1. Scope 1.1 This guide covers the design and construction of solid fuel burning masonry heaters. It provides dimensions for site constructed masonry heater components and clearances that have been derived by experience and found to be consistent with the safe installation of those masonry heaters. 1.2 Values given in SI units are to be regarded as standard. Inch/pound units may be rounded (see ). All dimensions are nominal unless specifically stated otherwise. All clearances listed in this guide are actual dimensions. 1.3 This guide applies to the design and construction of masonry heaters built on-site with the components and materials specified herein. It does not apply to the construction/installation requirements for component systems that have been safety tested and listed. The requirements for listed masonry heater systems are specified in the manufacturer's installation instructions. 1.4 The design and construction of solid fuel burning masonry heaters shall comply with applicable building codes.
ASTM Standards C11 Terminology Relating to Gypsum and Related Building Materials and Systems C43 Terminology of Structural Clay Products C71 Terminology Relating to Refractories C270 Specification for Mortar for Unit Masonry C401 Classification of Alumina and Alumina-Silicate Castable Refractories E136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C UL Standards UL103 Chimneys, Factory Built Residential Type and Building Heating AppliancesKeywords brick; Contraflow; firebrick; fire clay mortar; Grundofen; Kachelofen; Kakelugn; masonry heater; mortar; refractory mortar; Russian; soapstone refractory mortar; Solid fuel-burning masonry heaters; Construction; Contraflow; Brick; Firebrick; Fire clay mortar; Grundofen; Kachelofen/Kakelugn; Masonry heater; Mortar; Refractory mortar; Russian; Soapstone refractory mortar; ICS Code ICS Number Code 25.180.20 (Fuel furnaces) DOI: 10.1520/E1602-03R10E01 ASTM International is a member of CrossRef. ASTM E1602This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|