ASTM E1210-05
Historical Standard: ASTM E1210-05 Standard Test Method for Fluorescent Liquid Penetrant Examination Using the Hydrophilic Post-Emulsification Process
SUPERSEDED (see Active link, below)
ASTM E1210
1. Scope
1.1 This test method covers procedures for fluorescent penetrant examination utilizing the hydrophilic post-emulsification process. It is a nondestructive testing method for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks, or lack of fusion and is applicable to in-process, final, and maintenance examination. It can be effectively used in the examination of nonporous, metallic materials, both ferrous and nonferrous, and of nonmetallic materials such as glazed or fully densified ceramics and certain nonporous plastics and glass.
1.2 This test method also provides a reference:
1.2.1 By which a fluorescent penetrant examination hydrophilic post-emulsification process recommended or required by individual organizations can be reviewed to ascertain their applicability and completeness.
1.2.2 For use in the preparation of process specifications dealing with the fluorescent penetrant examination of materials and parts using the hydrophilic post-emulsification process. Agreement by the purchaser and the manufacturer regarding specific techniques is strongly recommended.
1.2.3 For use in the organization of the facilities and personnel concerned with the liquid penetrant examination.
1.3 This test method does not indicate or suggest standards for evaluation of the indications obtained. It should be pointed out, however, that indications must be interpreted or classified and then evaluated. For this purpose there must be a separate code or specification or a specific agreement to define the type, size, location, and direction of indications considered acceptable, and those considered unacceptable.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 All areas of this test method may be open to agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method)
D516 Test Method for Sulfate Ion in Water
D808 Test Method for Chlorine in New and Used Petroleum Products (High Pressure Decomposition Device Method)
D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)
E165 Practice for Liquid Penetrant Examination for General Industry
E433 Reference Photographs for Liquid Penetrant Inspection
E543 Specification for Agencies Performing Nondestructive Testing
E1316 Terminology for Nondestructive Examinations
ASNT Documents
ANSI/ASNT-CP-189 Standard for Qualification and Certification of Nondestructive Testing PersonnelMilitary Standard
MIL-STD-410 Nondestructive Testing Personnel Qualification and Certification Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.AIA Standard
2.6 Order of PrecedenceIn the event of conflict between this practice and the references cited herein, this practice takes precedence.Keywords
fluorescent liquid penetrant testing; hydrophilic post-emulsification method; nondestructive testing; Aerosol spray applications; Black light inspection; Ceramic materials/applications; Cold shuts; Contaminant removal; Cracking; Dwell test; Electrostatic spray application; Ferrous metals/alloys; Fluorescent liquid penetrant testing; Glass; Hydrophilic emulsifiers; Impurities; Laminations; Leak testing; Liquid penetration; Nonferrous metals/alloys; Nonporous metallic/nonmetallic materials; Penetrant inspection; Porosity; Seams; Surface analysis--metals/alloys;
ICS Code
ICS Number Code 19.100 (Non-destructive testing)
DOI: 10.1520/E1210-05
ASTM International is a member of CrossRef.