FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D7446 2009ASTM D7446 - 09Standard Specification for Structural Insulated Panel (SIP) Adhesives for Laminating Oriented Strand Board (OSB) to Rigid Cellular Polystryene Thermal Insulation Core MaterialsActive Standard ASTM D7446 | Developed by Subcommittee: D14.70 Book of Standards Volume: 15.06 ASTM D7446Abstract This specification addresses the physical, chemical and test requirements for structural insulated panel (SIP) adhesives suitable for the bonding of oriented strand boards (OSB) to rigid cellular polystyrene thermal insulation core materials for general structural use. Douglas-fir to Douglas-fir assemblies shall pass the following qualification requirements when tested in accordance with referenced ASTM documents enumerated herein: block shear strength (dry shear, soak/re-dry, oxidation resistance, and mold resistance); tensile strength (dry tensile bond strength, soak/re-dry, and mold resistance); and creep resistance. OSB to core to OSB assemblies shall, alternatively, be tested and pass shear strength and tensile (flat wise) bond strength requirements as well. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Significance and Use This specification addresses minimum performance criteria for adhesives used to laminate oriented strand board (OSB) structural panel facing material to expanded or extruded polystyrene core materials. Adhesive performance is based on tests that simulate exposure to moisture, temperature, seasonal weathering, and creep. Additionally, the adhesive is to demonstrate resistance to oxidation, mold, chemical reagents, and compatibility to the specific laminating materials. The adhesive manufacturers can use this specification for new product development and quality control purposes. Structural insulated panel manufacturers rely on an adhesive performance specification that determines its suitability before use. Performance of the SIP adhesive when evaluated in accordance with this specification aids in determining the suitability of the adhesive for laminating OSB facings to rigid cellular polystyrene core materials in the manufacture of structural insulated panels. 1. Scope 1.1 This specification is designed to evaluate adhesives suitable for the bonding of oriented strand board (OSB) to rigid cellular polystyrene insulation core materials for general structure use. 1.2 The requirements of the structural insulated panel (SIP) adhesive are based on the performance of the adhesive as measured by: 1.2.1 Resistance to shear by compression loading in ambient conditions and after accelerated aging. 1.2.2 Resistance to tensile loading in ambient conditions and after accelerated aging. 1.2.3 Resistance to creep (deformation) under static load in ambient conditions and after accelerated aging. 1.2.4 Tensile and shear strength to polystyrene core materials. 1.3 The classification of the adhesive formulation is based on, but not limited to the adhesive s industry accepted generic names, for example: phenol-resorcinol, emulsion polymer isocyanate, one and two-part urethane. The type of adhesive application and curing terminology are also usually included for classification purposes such as cold-setting phenol resorcinol, heat-cured phenol resorcinol, and hot melt one component urethane. 1.4 Evaluation of adhesive performance at high temperature conditions, such as during a fire exposure, is beyond the scope of this specification. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards C273/C273M Test Method for Shear Properties of Sandwich Core Materials C297/C297M Test Method for Flatwise Tensile Strength of Sandwich Constructions C578 Specification for Rigid, Cellular Polystyrene Thermal Insulation D572 Test Method for Rubber--Deterioration by Heat and Oxygen D905 Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading D907 Terminology of Adhesives D1183 Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions D1583 Test Method for Hydrogen Ion Concentration of Dry Adhesive Films D2294 Test Method for Creep Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal) D4300 Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi D4442 Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials D4444 Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters E4 Practices for Force Verification of Testing Machines Other Standards ISO17025 General Requirements for the Competence of Testing and Calibration Laboratories Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.Keywords building component; construction materials; engineered wood; lamination; structural insulated panel; ICS Code ICS Number Code 83.180 (Adhesives) DOI: 10.1520/D7446-09 ASTM International is a member of CrossRef. ASTM D7446The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|