|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D7199 2012ASTM D7199 - 07(2012)Standard Practice for Establishing Characteristic Values for Reinforced Glued Laminated Timber (Glulam) Beams Using Mechanics-Based ModelsActive Standard ASTM D7199 | Developed by Subcommittee: D07.02 Book of Standards Volume: 04.10 ASTM D7199Abstract This practice covers mechanics-based models for calculating characteristic values for the strength and stiffness of reinforced structural glued laminated timbers (glulam). The mechanics-based analyses shall account for the following: (1) stress-strain relationships for wood laminations and reinforcement; (2) strain compatibility; (3) equilibrium; (4) variability of mechanical properties; (5) volume effects; (6) finger-joint effects; (7) laminating effects; and (8) stress concentrations at the termination of reinforcement in beams with partial length reinforcement. This practice also provides for minimum physical test requirements to validate mechanics-based models. A minimum set of performance-based durability test requirements for reinforced glulams is also herein described. Additional durability test requirements shall be considered in accordance with the specific end-use environment. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This practice covers mechanics-based requirements for calculating characteristic values for the strength and stiffness of reinforced structural glued laminated timbers (glulam) manufactured in accordance with applicable provisions of ANSI/AITC A190.1 , subjected to quasi-static loadings. It addresses methods to obtain bending properties parallel to grain, about the x-x axis (F bx and E x ) for horizontally-laminated reinforced glulam beams. Secondary properties such as bending about the y-y axis (F by ), shear parallel to grain (F vx and F vy ), tension parallel to grain (F t ), compression parallel to grain (F c ), and compression perpendicular to grain (F c ?) are beyond the scope of this practice. When determination of secondary properties is deemed necessary, testing according to other applicable methods, such as Test Methods D143 , D198 or analysis in accordance with Practice D3737 , is required to establish these secondary properties. Reinforced glulam beams subjected to axial loads are outside the scope of this standard. This practice also provides minimum test requirements to validate the mechanics-based model. 1.2 The practice also describes a minimum set of performance-based durability test requirements for reinforced glulams, as specified in Annex A1 . Additional durability test requirements shall be considered in accordance with the specific end-use environment. Appendix X1 provides an example of a mechanics-based methodology that satisfies the requirements set forth in this standard. 1.3 Characteristic strength and elastic properties obtained using this standard may be used as a basis for developing design values. However, the proper safety, serviceability and adjustment factors including duration of load, to be used in design are outside the scope of this standard. 1.4 This practice does not cover unbonded reinforcement, prestressed reinforcement, nor shear reinforcement. 1.5 The values stated in SI units are to be regarded as standard. The mechanics based model may be developed using SI or in.-lb units. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D9 Terminology Relating to Wood and Wood-Based Products D143 Test Methods for Small Clear Specimens of Timber D198 Test Methods of Static Tests of Lumber in Structural Sizes D905 Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading D1990 Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens D2559 Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions D2915 Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products D3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite Materials D3410/D3410M Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading D3737 Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam) D4761 Test Methods for Mechanical Properties of Lumber and Wood-Base Structural Material D5124 Practice for Testing and Use of a Random Number Generator in Lumber and Wood Products Simulation Other Standard ANSI/AITCA190.1 Structural Glued Laminated Timber Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.Keywords ICS Code ICS Number Code 79.060.99 (Other wood-based panels) DOI: 10.1520/D7199-07R12 ASTM International is a member of CrossRef. ASTM D7199This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|