FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D7020 2012ASTM D7020 - 05(2012)Standard Performance Specification for Woven Blouse, Dress, Dress Shirt & Sport Shirt FabricsActive Standard ASTM D7020 | Developed by Subcommittee: D13.61 Book of Standards Volume: 07.02 ASTM D7020Abstract This performance specification covers fabrics for woven blouses, dresses, dress shirts, and sport shirts. It is not however applicable to woven fabrics used for interlinings. These requirements apply to the length and width directions for those properties where fabric direction is pertinent. The fabrics shall meet the following performance requirements: breaking strength which shall be determined using a constant rate of extension tensile testing machine; resistance to yarn slippage; tearing strength; dimensional change during pressing and finishing, after laundering, or after dry cleaning; colorfastness to laundering and dry cleaning; shade change due to sodium hypochlorite bleaching or non-chlorine bleaching, burnt gas fumes, dry and wet crocking, perspiration, and xenon-arc light; fabric smoothness after pressing, laundering, and dry cleaning; and flammability. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Significance and Use Fabrics intended for this end-use should meet all of the requirements listed in Table 1. It should be recognized that fabrics can be produced utilizing an almost infinite number of combinations of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. TABLE 1 Performance Requirements for Woven Blouse, Dress, Dress Shirt & Sport Shirt Fabrics
A There is more than one method that can be used to measure breaking strength tearing strength and colorfastness. These methods cannot be used interchangeably since there may be no overall correlation between them (see Note 2, Note 3, and Note 5). 1. Scope 1.1 This performance specification covers fabrics for woven blouses, dresses, dress shirts, and sport shirts. 1.2 This performance specification is not applicable to woven fabrics used for interlinings. 1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 When a fabric requires special treatment, specific methods will be described as they are developed for that material, and such special tests will have precedence over these general requirements. 1.5 The following precautionary caveat pertains only to the test methods described in this performance specification: This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
ASTM Standards D123 Terminology Relating to Textiles D434 Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam D1424 Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus D2261 Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) D5034 Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) D7022 Terminology Relating to Apparel AATCC Methods 188 Colorfastness to Sodium Hypochlorite Bleach in Home LaunderingFederal Standards 16CFR1610 Flammable Fabrics Act RegulationsKeywords blouse; dress; dress shirt; sport shirt.; Dresses; Blouse fabrics; Dress shirts; Shirt fabrics; Woven fabrics; Woven textile fabrics--specifications ICS Code ICS Number Code 61.020 (Clothes) DOI: 10.1520/D7020-05R12 ASTM International is a member of CrossRef. ASTM D7020This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|