ASTM D6255/D6255M-05
Historical Standard: ASTM D6255/D6255M-05 Standard Specification for Steel or Aluminum Slotted Angle Crates
SUPERSEDED (see Active link, below)
ASTM D6255 / D6255M
1. Scope
1.1 This specification covers the material and fabrication of new reusable metal (slotted angle) crates intended for use as containers for domestic and overseas shipment of lightweight airframe components and lightweight bulky items, not exceeding 3000 lb [1361 kg] for domestic or overseas air and surface shipments.
1.2 Slotted angle crate performance is dependent on its fabricated components; therefore, a variety of types, classes, and styles reflecting varied performance are specified. This specification, however, does not cover slotted angle crate performance under all atmosphere, handling, shipping, and storage conditions.
1.3 If the use of other construction methods or techniques are acceptable and permitted (see ), the resulting packaging systems shall be of equal or better performance than would result from the use of these specified materials and procedures. The appropriate distribution cycle specified in Practice D 4169 can be used to develop comparative procedures and criteria.
1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. See IEEE/ASTM SI 10 for conversion of units.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of the standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A109/A109M Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
A123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel
D996 Terminology of Packaging and Distribution Environments
D1990 Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens
D3951 Practice for Commercial Packaging
D3953 Specification for Strapping, Flat Steel and Seals
D4169 Practice for Performance Testing of Shipping Containers and Systems
D4727/D4727M Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes
D6199 Practice for Quality of Wood Members of Containers and Pallets
F1667 Specification for Driven Fasteners: Nails, Spikes, and Staples
IEEE/ASTM SI 10 Standard for Use of the International System of Units (SI): The Modern Metric System
Federal Specifications
TT-W-572 Wood Preservative: Water-Repellent Available from the Federal Supply Service Bureau, Specification Section, Suite 8100, 480 LEnfant Plaza, SW, Washington, DC 20408.National Institute of Standards and Technology (NIST)
PS1-95 Construction and Industrial Plywood Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.Keywords
airframe components crate; angle; crate; packaging; shipping container; slotted angle; Airframe components crate; Aluminum shipping crates; Angle crates; Crates; Domestic shipping; Overseas shipping containers; Shipping containers/materials/applications--specifications; Slotted angle crates; Steel shipping crates ;
ICS Code
ICS Number Code 55.160 (Cases. Boxes. Crates)
DOI: 10.1520/D6255_D6255M-05
ASTM International is a member of CrossRef.
