FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D6141 2009ASTM D6141 - 09Standard Guide for Screening Clay Portion of Geosynthetic Clay Liner (GCL) for Chemical Compatibility to LiquidsActive Standard ASTM D6141 | Developed by Subcommittee: D35.04 Book of Standards Volume: 04.13 ASTM D6141Significance and Use This guide is intended as a starting place for those wishing to investigate the chemical compatibility of the clay portion of a geosynthetic clay liner to test liquids. Within the scope of this guide, the clay portion of a geosynthetic clay liner that is chemically compatible with a test liquid may be expected to maintain its swelling characteristics. Conversely, the clay portion of a geosynthetic clay liner that is incompatible with a test liquid may be expected not to maintain its swelling characteristics. In instances where the compatibility of the clay portion of a GCL is questionable, additional hydraulic testing under the expected site conditions may be warranted. 1. Scope 1.1 This guide covers procedures and test methods that can be used in the evaluation of the ability of the clay portion of a geosynthetic clay liner to resist change due to exposure to liquids. These liquids may come from a site, or be generated in a laboratory from a site-specific soil. 1.2 The scope of this guide is limited to short-term screening and is not intended to replace evaluation procedures that measure a performance property such as EPA 9100, Test Method D6766 , or other suitable ASTM standards as they become available. This guide does not address potential adverse effects of wet-dry cycling. 1.3 This guide applies to the clay component of a GCL. The synthetic carrier components are covered independently as described in Practice D5322 . 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D653 Terminology Relating to Soil, Rock, and Contained Fluids D4439 Terminology for Geosynthetics D5322 Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids D5890 Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners D5891 Test Method for Fluid Loss of Clay Component of Geosynthetic Clay Liners D6072 Practice for Obtaining Samples of Geosynthetic Clay Liners D6766 Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Liquids Other Document EPATestMethod9100 Saturated Hydraulic Conductivity, Saturated Leachate Conductivity, and Intrinsic PermeabilityKeywords chemical compatibility; fluid loss; geosynthetic clay liner; leachate; swell index; Screen analysis--water; Short term screening; Swell index; Chemical compatibility; Fluid loss; Geosynthetic clay liner (GCL); Screen analysis; ICS Code ICS Number Code 65.020.40 (Landscaping and silviculture); 91.100.50 (Binders. Sealing materials) DOI: 10.1520/D6141-09 ASTM International is a member of CrossRef. ASTM D6141The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|