FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D5933 2013ASTM D5933 - 96(2013)Standard Specification for 2 5/8-in. and 4-in. Diameter Metal Shear Plates for Use in Wood ConstructionsActive Standard ASTM D5933 | Developed by Subcommittee: D07.05 Book of Standards Volume: 04.10 ASTM D5933Abstract This specification covers standardizing the dimensions and materials for the manufacture of steel or cast iron shear plates used in the fabrication of connections in wood constructions. This specification covers the two basic diameters of metal shear plates commonly used in North American timber construction. Shear plates shall be free from any casting defects that would hinder normal installation and performance. Shear plates shall conform to the specified requirements for the following: (1) marking (2) nail attachment holes, (3) draft casting on the rim and on the hub, (4) central bolt or lag screw holes, (5) furnishing with or without galvanization, and (6) fit and finish. The geometry and dimensional requirements for stamped steel shear plates and cast iron shear plates are specified and illustrated. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers standardizing the dimensions and materials for the manufacture of 2 5 / 8 and 4-in. diameter steel or cast iron shear plates used in the fabrication of connections in wood constructions. The referencing of this specification in design, construction, and purchase order documents gives the using parties ensurance that the shear plates to be used in an assembly meet minimum materials quality standards and that dimensions for fabrication and finish can be relied on to ensure connection performance. This specification provides regulatory agencies with a set of standards by which to judge the acceptability of shear plates encountered in the field and in fabricators' shops. 1.2 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only. 1.3 Safety Hazards There are no known hazards with the use of this specification. The products manufactured to this specification should not be brittle or difficult to install with proper tools.
ASTM Standards A47/A47M Specification for Ferritic Malleable Iron Castings A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware A570/A570M Specification for Structural Steel, Sheet and Strip, Carbon, Hot-Rolled A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process Other Document AISI/SAE No. 1010 Carbon Steel, Steel Products Manual, Plates, Iron and Steel SocietyKeywords connections; connectors; structural timber; timber joints; wood; wood constructions ; ICS Code ICS Number Code 91.080.20 (Timber structures) DOI: 10.1520/D5933-96R13 ASTM International is a member of CrossRef. ASTM D5933This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|