FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D5156 2008ASTM D5156 - 02(2008)Standard Test Methods for Continuous Measurement of Ozone in Ambient, Workplace, and Indoor Atmospheres (Ultraviolet Absorption)Active Standard ASTM D5156 | Developed by Subcommittee: D22.03 Book of Standards Volume: 11.07 ASTM D5156Significance and Use Standards for O 3 in the atmosphere have been promulgated by government authorities to protect the health and welfare of the public (5) and also for the protection of industrial workers (6) . Although O 3 itself is a toxic material, in ambient air it is primarily the photochemical oxidants formed along with O 3 in polluted air exposed to sunlight that cause smog symptoms such as lachrymation and burning eyes. Ozone is much more easily monitored than these photochemical oxidants and provides a good indication of their concentrations, and it is therefore the substance that is specified in air quality standards and regulations. 1. Scope 1.1 This test method describes the sampling and continuous analysis of ozone (O 3 ) in the atmosphere at concentrations ranging from 10 to 2000 ? g/m 3 of O 3 in air (5 ppb(v) to 1 ppm(v)). 1.1.1 The test method is limited to applications by its sensitivity to interferences as described in Section 6. The interference sensitivities may limit its use for ambient and workplace atmospheres. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D1356 Terminology Relating to Sampling and Analysis of Atmospheres D1357 Practice for Planning the Sampling of the Ambient Atmosphere D1914 Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres D3249 Practice for General Ambient Air Analyzer Procedures D3631 Test Methods for Measuring Surface Atmospheric Pressure D3670 Guide for Determination of Precision and Bias of Methods of Committee D22 D5011 Practices for Calibration of Ozone Monitors Using Transfer Standards D5110 Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry Other Documents EPA-600/4-77-027a, Quality Assurance Handbook for Air Pollution Measurement Systems, Vol II, Ambient Air Specific MethodsKeywords ambient atmospheres; indoor atmospheres; monitoring; ozone; ultraviolet absorption; workplace atmospheres; Air monitoring; Ambient air/atmospheric analysis; Continuous measurement/monitoring--atmospheric analysis; Indoor air analysis; Ozone (O 3 ); Photometry; Ultraviolet (UV) analysis--atmospheric applications; Workplace air/atmospheres; ICS Code ICS Number Code 13.040.30 (Workplace atmospheres) DOI: 10.1520/D5156-02R08 ASTM International is a member of CrossRef. ASTM D5156This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|