FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D4491 2009ASTM D4491 - 99a(2009)Standard Test Methods for Water Permeability of Geotextiles by PermittivityActive Standard ASTM D4491 | Developed by Subcommittee: D35.03 Book of Standards Volume: 04.13 ASTM D4491Significance and Use These test methods are considered satisfactory for acceptance testing of commercial shipments of geotextiles since the methods have been used extensively in the trade for acceptance testing. In case of a dispute arising from differences in reported test results when using these test methods for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the start of testing. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in light of the known bias. Permittivity is an indicator of the quantity of water that can pass through a geotextile in an isolated condition. As there are many applications and environmental conditions under which a geotextile may be used, care should be taken when attempting to apply the results of these test methods to the field performance of a geotextile. Since there are geotextiles of various thicknesses in use, evaluation in terms of their Darcy coefficient of permeabilities can be misleading. In many instances, it is more significant to evaluate the quantity of water that would pass through a geotextile under a given head over a particular cross-sectional area; this is expressed as permittivity. If the permeability of an individual geotextile is of importance, a nominal coefficient of permeability, as related to geotechnical engineering, may be computed. By multiplying permittivity times the nominal thickness of the geotextile, as determined by Test Method D5199 , the nominal coefficient of permeability is obtained. Note 2The nominal thickness is used as it is difficult to evaluate the pressure on the geotextile during the test, thereby making it difficult to determine the thickness of the fabric under these test conditions. 1. Scope 1.1 These test methods cover procedures for determining the hydraulic conductivity (water permeability) of geotextiles in terms of permittivity under standard testing conditions, in the uncompressed state. Included are two procedures: the constant head method and the falling head method. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units stated in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D123 Terminology Relating to Textiles D653 Terminology Relating to Soil, Rock, and Contained Fluids D4439 Terminology for Geosynthetics D5199 Test Method for Measuring the Nominal Thickness of Geosynthetics E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method Keywords constant head; falling head; geotextiles; permeability; permittivity; Constant head testing; Drainage materials/systems; Falling head test; Flow and flow rate--soil/rock/related materials; Geosynthetics; Hydraulic conductivity/transmissivity; Liquids--geosynthetic/geothermal applications; Penetration--soil; Permeability--geosynthetics; Permittivity method; Water analysis; Water penetration; ICS Code ICS Number Code 59.080.70 (Geotextiles) DOI: 10.1520/D4491-99AR09 ASTM International is a member of CrossRef. ASTM D4491The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|