1. Scope

1.1 This specification covers unpigmented, unsupported, sheet or tubular, medium-density polyethylene films (hereafter referred to as film or films) from resins having densities in the range from 926.0 to 938.0 kg/m (0.926 to 0.938 g/cm ), inclusive, as measured on molded plaques.

1.2 This specification is applicable to homopolymer polyethylene but is not restricted to it.

1.3 This specification is also applicable to films made from copolymer polyethylene commonly referred to in industry as low-pressure polyethylene.

1.4 This specification is also applicable to films made from blends of homopolymers and copolymers, including ethylene/vinyl-acetate copolymers.

1.5 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all the requirements of this specification are met and as long as any specific requirements as governed by the producer and end user are also met (see Note 1).

1.6 While much of the content of this specification may also be applied to colored or pigmented films, special care must be exercised. This specification does not address specific problems associated with coloring, such as, quantity and quality of pigment dispersion, optical properties, and increase in density. These and other areas must be taken into account by mutual agreement between the supplier and the purchaser.

1.7 The thickness of the films covered by this specification range from 25 to 100 [mu]m (0.001 to 0.004 in.), inclusive. The maximum width of the sheet or lay-flat is 3.05 m (120 in.).

1.8 This specification does not cover oriented heat-shrinkable films.

1.9 This specification defines the levels of the various physical properties from which specifications for specific films may be described. The levels of physical properties required by a film for a given application are selected from Section 6 and the corresponding tables. However, Sections 2 to 5 relating to tolerances shall apply without change to all film falling within the scope indicated by the title and 1.1,

1.2, 1.3, and 1.4.

1.10 This specification covers dimensional tolerances, classification, intrinsic quality requirements, and test methods. The dimensional tolerances include thickness, width, and length or yield. Classification defines types, classes, surfaces, and finishes. The intrinsic quality requirements include density, workmanship, impact strength, tensile strength, heat sealability, and odor, as well as the classification properties for stiffness, coefficient of friction, optical properties, and surface treatment. A sampling method is included.

1.11 The values stated in SI units are to be regarded as the standard. The values in parentheses are given for information only.

1.12 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D882 Test Method for Tensile Properties of Thin Plastic Sheeting

D883 Terminology Relating to Plastics

D1003 Test Method for Haze and Luminous Transmittance of Transparent Plastics

D1505 Test Method for Density of Plastics by the Density-Gradient Technique

D1709 Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting

D1898 Practice for Sampling of Plastics

D2103 Specification for Polyethylene Film and Sheeting

D2457 Test Method for Specular Gloss of Plastic Films and Solid Plastics

D2578 Test Method for Wetting Tension of Polyethylene and Polypropylene Films

D4321 Test Method for Package Yield of Plastic Film

D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

D4883 Test Method for Density of Polyethylene by the Ultrasound Technique

D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials

D6988 Guide for Determination of Thickness of Plastic Film Test Specimens

D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products

E1870 Test Method for Odor and Taste Transfer from Polymeric Packaging Film

F88 Test Method for Seal Strength of Flexible Barrier Materials

Keywords

film; general use; medium-density; packaging; polyethylene; recycled; Packing/packaging materials/systems (plastics); Plastic sheet and film--specifications; Polyethylene (PE) sheet and film--specifications; Packing/packaging materials/systems--specifications;

ICS Code

ICS Number Code 55.040 (Packaging materials and accessories)

DOI: 10.1520/D3981-95

ASTM International is a member of CrossRef.