FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D3935 2009ASTM D3935 - 09Standard Specification for Polycarbonate (PC) Unfilled and Reinforced MaterialActive Standard ASTM D3935 | Developed by Subcommittee: D20.15 Book of Standards Volume: 08.02 ASTM D3935Abstract This specification covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions may also find use for compression molding or application from solution. Unfilled polycarbonate materials are classified into groups according to their composition. The groups are Group 01, Group 02, Group 03, Group 04, Group 05, and Group 06. These groups are subdivided into classes which are Class 0, Class 1, Class 2, Class 3, and Class 4 and these classes can be further be subdivided into grades which are Grade 1, Grade 2, Grade 3, Grade 4, Grade 5, Grade 6, Grade 7 and Grade 0. Different tests shall be conducted in order to determine the following properties of polymer materials: Izod impact strength, flexural modulus, tensile strength, and deflection temperature. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions may also find use for compression molding or application from solution. 1.2 The properties in this specification are those required for identifying the compositions covered. There may be other requirements necessary for identifying particular characteristics important to specific applications. Those may be specified by using the suffixes in accordance with Section 5. 1.3 The values stated in SI units are to be regarded as the standard. Note 1This specification and ISO 7391-1 and ISO 7391-2 address the same subject matter, but differ in technical content. 1.4 The following hazards caveat pertains only to the test methods portion, Section 12, of this specification. This standard does not purport to address all safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability or regulatory limitations prior to use.
ASTM Standards D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics D638 Test Method for Tensile Properties of Plastics D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement D883 Terminology Relating to Plastics D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer D1600 Terminology for Abbreviated Terms Relating to Plastics D2584 Test Method for Ignition Loss of Cured Reinforced Resins D3892 Practice for Packaging/Packing of Plastics D4000 Classification System for Specifying Plastic Materials D5630 Test Method for Ash Content in Plastics E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E169 Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis ISO Standard ISO 7391-2 Plastics--Polycarbonate Molding and Extrusion Materials (Part 2: Preparation of Test Specimens and Determination of Properties)Keywords line-callout specification; plastics; polycarbonate resins; recycled plastics; specification; Polycarbonate (PC)--specifications; Polymers--specifications; Recycled plastics--specifications; Extrusion compounds (plastic)--specifications; Line call-out specifications--plastics; Molding/extrusion compounds/materials--specifications; Plastics--specifications; ICS Code ICS Number Code 83.080.20 (Thermoplastic materials); 83.120 (Reinforced plast) DOI: 10.1520/D3935-09 ASTM International is a member of CrossRef. ASTM D3935The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|