|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D1681 2014ASTM D1681-05-Reapproved2014Withdrawn Standard: Standard Test Method for Synthetic Anionic Active Ingredient in Detergents by Cationic Titration Procedure (Withdrawn 2023)ASTM D1681Scope 1.1 Direct titration of an anionic surfactant with a standardized cationic reagent is a simple and convenient method for the quantitative determination of the content of active ingredient. The end point is detffected by the transfer of a colored complex from an organic solvent phase to an aqueous phase. The relationship between anionic and cationic agents is not always stoichiometric, and for maximum accuracy the anionic type of interest should first be characterized and then used to standardize the cationic reagent. In most cases, however, the different anionic surfactants likely to be encountered react in the same proportions. That is, a cationic titrating solution standardized against a characterized anionic agent can be used to analyze other anionics of known molecular weights. 1.2 This test method is applicable to alkylaryl sulfonates and fatty alkyl sulfates. Low results are obtained with alkylbenzene sulfonates having the alkyl chain length less than eight carbon atoms. Low results are also obtained for alkyl sulfates with the alkyl chain length of less than twelve carbon atoms. The anionic surfactants characterized in accordance with Sections 17 – 23 should be the sodium salt and not amine, ammonium, or potassium salts. In case only amine or ammonium salts are available, they should be first converted to the sodium salt before proceeding with this analysis.
1.3 The analytical procedures appear in the following order:
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazards statement, see Section 7. Keywords ICS Code ICS Number Code 71.100.40 (Surface active agents) DOI: 10.1520/D1681-05R14 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|