1. Scope

1.1 This practice outlines procedures for the petrographic examination of samples of hardened concrete. The samples examined may be taken from concrete constructions, they may be concrete products or portions thereof, or they may be concrete or mortar specimens that have been exposed in natural environments, or to simulated service conditions, or subjected to laboratory tests. The phrase 'concrete constructions' is intended to include all sorts of objects, units, or structures that have been built of hydraulic cement concrete.

1.2 The petrographic procedures outlined herein are applicable to the examination of samples of all types of hardened hydraulic-cement mixtures, including concrete, mortar, grout, plaster, stucco, terrazzo, and the like. In this practice, the material for examination is designated as 'concrete,' even though the commentary may be applicable to the other mixtures, unless the reference is specifically to media other than concrete.

1.3 Annex A1 outlines an uranyl acetate method for identifying locations where alkali-silica gel may be present. It is a requirement that the substances in those locations must be identified using any other more definitive techniques, such as petrographic microscopy.

1.4 The purposes of and procedures for petrographic examination of hardened concrete are given in the following sections:

1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information purposes only.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazard statement is given in 5.2.10.1.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C125 Terminology Relating to Concrete and Concrete Aggregates

C215 Test Method for Fundamental Transverse, Longitudinal, and Torsional Resonant Frequencies of Concrete Specimens

C227 Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)

C342 Test Method for Potential Volume Change of Cement-Aggregate Combinations

C441 Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction

C452 Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate

C457 Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete

C496/C496M Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens

C597 Test Method for Pulse Velocity Through Concrete

C803/C803M Test Method for Penetration Resistance of Hardened Concrete

C805 Test Method for Rebound Number of Hardened Concrete

C823 Practice for Examination and Sampling of Hardened Concrete in Constructions

C1012 Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

C1260 Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)

E3 Guide for Preparation of Metallographic Specimens

E883 Guide for Reflected-Light Photomicrography

ASTM Adjuncts

AdjunctC856(ADJCO856 A chart of 27 photos Available from ASTM International Headquarters. Order Adjunct No. . Original adjunct produced in 1995.

Keywords

aggregates; air voids; alkali-silica reaction; analysis; deterioration; examination; fire effects; hardened concrete; microscopy; paste; petrographic; secondary deposits; Fire testing--building materials; Hardened concrete; Microscopic examination--concrete; Petrographic analysis; Stereomicroscopy; Visual examination--concrete; Alkali reactivity;

ICS Code

ICS Number Code 91.100.30 (Concrete and concrete products)

DOI: 10.1520/C0856-95E01

ASTM International is a member of CrossRef.