FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-B745 2012ASTM B745 / B745M - 12Standard Specification for Corrugated Aluminum Pipe for Sewers and DrainsActive Standard ASTM B745 / B745M | Developed by Subcommittee: B07.08 Book of Standards Volume: 02.02 ASTM B745 / B745MAbstract This specification covers corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. All pipe fabricated under this specification shall be formed from aluminum-alloy sheet conforming to the requirements specified. The sheet used in fabricating coupling bands shall conform to the requirements specified. The material used for rivets in riveted pipe shall conform to the requirements specified. Bolts and nuts for coupling bands shall conform to the required specification. If gaskets are used in couplings, they shall be a band of expanded rubber meeting the specified requirements. The fabrication requirements for type I, type II, type IA, and type IR pipe are presented. The corrugations shall be either annular or helical as provided. The different pipe requirements like pipe dimensions, sheet thickness, pipe-arch dimensions, longitudinal seams, and perforations are presented in details. Field joints for each type of corrugated aluminum pipe shall maintain pipe alignment during construction and prevent infiltration of fill material during the life of the installation. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. 1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth-cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the sheet thickness. The structural design of corrugated aluminum pipe and the proper installation procedures are given in Practices B790/B790M and B788/B788M , respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe is given in Practice A930 . 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength A563 Specification for Carbon and Alloy Steel Nuts A563M Specification for Carbon and Alloy Steel Nuts (Metric) A930 Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate B209M Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes B221M Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) B316/B316M Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel B666/B666M Practice for Identification Marking of Aluminum and Magnesium Products B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel B744/B744M Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe B788/B788M Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe B790/B790M Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits C443 Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber F467 Specification for Nonferrous Nuts for General Use F467M Specification for Nonferrous Nuts for General Use (Metric) F468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use F468M Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric) F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric) F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs F594 Specification for Stainless Steel Nuts F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs F836M Specification for Style 1 Stainless Steel Metric Nuts (Metric) Keywords aluminum culvert; aluminum storm drains; culvert pipe; storm drain pipe ; ICS Code ICS Number Code 23.040.15 (Non-ferrous metal pipes) DOI: 10.1520/B0745_B0745M-12 ASTM International is a member of CrossRef. ASTM B745 / B745MThe following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|