FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-F2379 2010ASTM F2379 - 04(2010)Standard Test Method for Energy Performance of Powered Open Warewashing SinksActive Standard ASTM F2379 | Developed by Subcommittee: F26.06 Book of Standards Volume: 15.12 ASTM F2379Significance and Use The energy input rate test is used to confirm that the powered sink is operating properly prior to further testing. Preheat energy and time can be useful to food service operators to manage power demands and to know how quickly the powered sink can be ready for operation when filled with cold water. Note 2It is typically recommended that powered sinks be filled with hot water prior to use. This test is useful for operations that have a limited supply of domestic hot water and would need to use cold water to fill the sink to capacity. Idle energy rate and pilot energy rate can be used to estimate energy consumption during standby periods. Washing cycle energy consumption can be used by the food service operator to estimate energy consumption during operating periods. 1. Scope 1.1 This test method evaluates the energy consumption of powered open warewashing sinks. The food service operator can use these tests to evaluate and select a suitable washing device and understand its energy consumption. 1.2 This test method applies to powered open warewashing sinks (powered sinks) with the following characteristics: a large main water sink with electrically powered water pump(s) and multiple high flow water nozzles. The unit may include gas or electric heaters to maintain water temperature. These powered sinks are designed to run for predetermined cycle duration and accommodate pots and pans of various shapes and sizes as well as cooking utensils. They are intended for stand alone use and require little supervision. The powered sink will be tested for the following (where applicable): 1.2.1 Maximum energy input rate (10.2), 1.2.2 Preheat energy consumption and duration (10.3), 1.2.3 Idle energy rate (10.4), 1.2.4 Pilot energy rate, if applicable (10.5), and 1.2.5 Washing cycle energy consumption (10.6). Note 1This test method applies only to the powered portion of the unit. Other compartments (sanitizing, rinsing, and so forth) are not evaluated. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D3588 Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels ANSI Standard 2000InternationalFueASHRAE Documents ASHRAE1993 Fundamentals HandbookKeywords duty cycle; energy consumption; powered sink; powered warewashing sink; test method; Cooking/food service equipment performance; Powered open warewashing sinks; Sinks; ICS Code ICS Number Code 97.060 (Laundry appliances) DOI: 10.1520/F2379-04R10 ASTM International is a member of CrossRef. ASTM F2379This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|