Course & CEU
Land Use and Development
Rules & Regulations
Description of ASTM-D7565 2010
ASTM D7565 / D7565M - 10
Standard Test Method for Determining Tensile Properties of Fiber Reinforced Polymer Matrix Composites Used for Strengthening of Civil Structures
Active Standard ASTM D7565 / D7565M | Developed by Subcommittee: D30.10
Book of Standards Volume: 15.03
ASTM D7565 / D7565M
Significance and Use
This test method can be used to obtain the tensile force capacity and ultimate tensile strain of FRP material used for the strengthening of other structural materials such as, metals, timber, and reinforced concrete. The principal test variables could be the FRP constituents and fabrication method or the size or type of FRP laminate. The obtained tensile properties can be used for material specifications, quality control and assurance, structural design and analysis, and research and development.
This test method focuses on the FRP material itself, irrespective of the gripping method. Therefore, maximum force and strain data associated with failure or pullout at either grip are disregarded. The force capacity and maximum strain measurements are based solely on test specimens that fail in the gauge section.
1.1 This test method describes the requirements for sample preparation, tensile testing, and results calculation of flat fiber reinforced polymer (FRP) composite materials used for the strengthening of structures made of materials such as metals, timber, masonry, and reinforced concrete. The method may be used to determine the tensile properties of wet lay-up and pre-impregnated FRP composites fabricated on site or manufactured in a factory setting. The FRP composite may be of either unidirectional (0-degrees) or cross-ply (0/90 type) reinforcement. For cross-ply laminates, the construction may be achieved using multiple-layers of unidirectional fibers at either 0 or 90 degrees, or one or more layers of stitched or woven 0/90 fabrics. The composite material forms are limited to continuous fiber or discontinuous fiber-reinforced composites in which the laminate is balanced and symmetric with respect to the test direction. The method only covers the determination of the tensile properties of the FRP composite material. Other components used to attach the FRP material to the substrate, such as the primer, putty, and adhesive in externally bonded strengthening systems, are excluded from the sample preparation and testing detailed in this document. This test method refers to Test Method D3039/D3039M for conduct of the tests.
1.2 The values stated in either SI units or inch-pound units are to be regarded as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
D883 Terminology Relating to Plastics
D3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite Materials
D3878 Terminology for Composite Materials
D5229/D5229M Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials
D5687/D5687M Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation
E6 Terminology Relating to Methods of Mechanical Testing
E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E456 Terminology Relating to Quality and Statistics
composite materials; modulus of elasticity; pre-cured FRP system; tensile properties; tensile strength; wet lay-up FRP system; Composite materials; Fiber reinforced polymers; Modulus of elasticity; Tensile properties/testing ;
ICS Number Code 83.120 (Reinforced plastics)
ASTM D7565 / D7565M
The following editions for this book are also available...
This book also exists in the following packages...
MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at email@example.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are:
- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at firstname.lastname@example.org or +1 800.798.9296.
ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
US LOCAL CODES
US Territory Code Adoptions / Amendments
US State Code Adoptions / Amendments