Land Use and Development
Rules & Regulations
Description of ASTM-D6778 2012
ASTM D6778 - 12
Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)
Active Standard ASTM D6778 | Developed by Subcommittee: D20.15
Book of Standards Volume: 08.03
This classification covers polyoxymethylene materials suitable for molding and extrusion. This specification allows for the use of polyoxymethylene plastic materials that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or combination thereof, provided that the requirements as stated in this specification are met. Test specimens shall be molded by injection molding and all test pieces shall be tested as molded and conditioned in the standard laboratory atmosphere. The mechanical properties of the unreinforced and reinforced, filled, or lubricated polyoxymethylene materials shall be determined and shall conform to the following requirements: flow rate; melting point; tensile strength; tensile modulus; Charpy impact resistance; and deflection temperature.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This classification system covers polyoxymethylene materials suitable for molding and extrusion. This classification system allows for the use of polyoxymethylene plastic materials that are recycled, reconstituted, recycled-regrind, recovered, or reprocessed, or combination thereof, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered, or reprocessed polyoxymethylene plastic materials, or combination thereof, to ensure compliance. (See Guide D7209 ).
1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.
1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
Note 1This classification system is similar to ISO 9988-1/-2, although the technical content is significantly different.
D618 Practice for Conditioning Plastics for Testing
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3892 Practice for Packaging/Packing of Plastics
D4000 Classification System for Specifying Plastic Materials
D5630 Test Method for Ash Content in Plastics
D6100 Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
acetal; acetal copolymer; acetal homopolymer; acetal terpolymer; classification; classification system; line callout; L-P-392A; MIL-P-46137A (MR); plastic materials; polyformaldehyde; polyoxymethylene; polyoxymethylene copolymer; polyoxymethylene homopolymer; polyoxymethylene terpolymer; POM; recycle; specification;
ICS Number Code 83.140.01 (Rubber and plastic products in general)
The following editions for this book are also available...
This book also exists in the following packages...
MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at firstname.lastname@example.org or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are:
- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at email@example.com or +1 800.798.9296.
ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
US LOCAL CODES
US Territory Code Adoptions / Amendments
US State Code Adoptions / Amendments