Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN IEC 61169-60:2021 Radio-frequency connectors - Sectional specification for RF coaxial connectors with push on mating. Characteristic impedance 50 Ohm (type SMPM), 2021
- undefined
- Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
- English [Go to Page]
- CONTENTS
- FOREWORD
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Mating face and gauge information [Go to Page]
- 4.1 Dimensions – General connectors – Grade 2 [Go to Page]
- 4.1.1 SMPM connector with pin-centre contact
- Figures [Go to Page]
- Figure 1 – SMPM connector with pin-centre contact –Full detent (for dimensions, see Table 1)
- Tables [Go to Page]
- Table 1 – Dimensions of SMPM connector with pin-centre contact full detent
- Figure 2 – SMPM connector with pin-centre contact –Smooth bore (for dimensions, see Table 2)
- Table 2 – Dimensions of SMPM connector with pin-centre contact – Smooth bore [Go to Page]
- 4.1.2 SMPM connector with socket-centre contact (see Figure 3)
- Figure 3 – SMPM connector with socket-centre contact(for dimensions, see Table 3)
- Table 3 – Dimensions of SMPM connector with socket-centre contact
- 4.2 SMPM gauges [Go to Page]
- 4.2.1 SMPM gauge pin for socket-centre contact
- Figure 4 – SMPM gauge pin for socket-centre contact(for dimensions, see Table 4)
- Table 4 – Dimensions of SMPM gauge pin for socket-centre contact [Go to Page]
- 4.2.2 Gauges for outer contact of SMPM connector with socket-centre contact
- Figure 5 – SMPM engagement force gauge –Full detent (for dimensions, see Table 5)
- Table 5 – Dimensions of SMPM engagement force gauge – Full detent
- Figure 6 – SMPM Separation force gauge –Full detent (for dimensions, see Table 6)
- Table 6 – Dimensions of SMPM separation force gauge – Full detent
- Figure 7 – SMPM Engagement force gauge –Smooth bore (for dimensions, see Table 7)
- Table 7 – Dimensions of SMPM engagement force gauge – Smooth bore
- Figure 8 – SMPM Separation force gauge –Smooth bore (for dimensions, see Table 8)
- Figure 9 – SMPM gauge block(for dimensions, see Table 9)
- Table 8 – Dimensions of SMPM separation force gauge – Smooth bore
- 5 Quality assessment procedure [Go to Page]
- 5.1 General
- 5.2 Rating and characteristics (see Clause 5 of IEC 61169-1:2013)
- Table 9 – Dimensions of SMPM gauge block
- Table 10 – Preferred climatic categories (see IEC 60068-1)
- Table 11 – Rating and characteristics
- 5.3 Test schedule and inspection requirements [Go to Page]
- 5.3.1 Acceptance tests
- 5.3.2 Periodic tests
- Table 12 – Acceptance tests
- Table 13 – Periodic tests
- 5.4 Procedures for the quality conformance [Go to Page]
- 5.4.1 Quality conformance inspection
- 5.4.2 Quality conformance and its maintenance
- 6 Instructions for preparation of detail specifications (DS) [Go to Page]
- 6.1 General
- 6.2 Identification of the component
- 6.3 Performances
- 6.4 Marking, ordering information and related matters
- 6.5 Selection of tests, test conditions and severities
- 6.6 Blank detail specification pro-forma for type SMPM connector
- 7 Marking [Go to Page]
- 7.1 Marking of component
- 7.2 Marking and contents of package [Go to Page]