|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E839 2023ASTM E839-23Redline Standard: Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple CableASTM E839Scope 1.1 This document lists methods for testing Mineral-Insulated, Metal-Sheathed (MIMS) thermocouple assemblies and thermocouple cable, but does not require that any of these tests be performed nor does it state criteria for acceptance. The acceptance criteria are given in other ASTM standard specifications that impose this testing for those thermocouples and cable. Examples from ASTM thermocouple specifications for acceptance criteria are given for many of the tests. These tabulated values are not necessarily those that would be required to meet these tests, but are included as examples only. 1.2 These tests are intended to support quality control and to evaluate the suitability of sheathed thermocouple cable or assemblies for specific applications. Some alternative test methods to obtain the same information are given, since in a given situation, an alternative test method may be more practical. Service conditions are widely variable, so it is unlikely that all the tests described will be appropriate for a given thermocouple application. A brief statement is made following each test description to indicate when it might be used. 1.3 The tests described herein include test methods to measure the following properties of sheathed thermocouple material and assemblies. 1.3.1 Insulation Properties: 1.3.1.1 Compaction—direct method, absorption method, and tension method. 1.3.1.2 Thickness. 1.3.1.3 Resistance—at room temperature and at elevated temperature. 1.3.2 Sheath Properties: 1.3.2.1 Integrity—two water test methods and mass spectrometer. 1.3.2.2 Dimensions—length, diameter, and roundness. 1.3.2.3 Wall thickness. 1.3.2.4 Surface—gross visual, finish, defect detection by dye penetrant, and cold-lap detection by tension test. 1.3.2.5 Metallurgical structure. 1.3.2.6 Ductility—bend test and tension test. 1.3.3 Thermoelement Properties: 1.3.3.1 Calibration. 1.3.3.2 Homogeneity. 1.3.3.3 Drift. 1.3.3.4 Thermoelement diameter, roundness, and surface appearance. 1.3.3.5 Thermoelement spacing. 1.3.3.6 Thermoelement ductility. 1.3.3.7 Metallurgical structure. 1.3.4 Thermocouple Assembly Properties: 1.3.4.1 Dimensions—length, diameter, and roundness. 1.3.4.2 Surface—gross visual, finish, reference junction end moisture seal, and defect detection by dye penetrant. 1.3.4.3 Electrical—continuity, loop resistance, and connector polarity. 1.3.4.4 Radiographic inspection. 1.3.4.5 Thermoelement diameter. 1.3.4.6 Thermal response time. 1.3.4.7 Thermal cycle. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords high temperature insulation test; insulation resistance; sheath integrity; sheathed thermocouple; thermal cycle; thermal response time; thermocouple; thermocouple assembly properties; thermoelement; thermoelement properties ; ICS Code ICS Number Code 17.200.20 (Temperature-measuring instruments) DOI: 10.1520/E0839-23 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|