FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D6023 2007ASTM D6023 - 07Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM)Active Standard ASTM D6023 | Developed by Subcommittee: D18.15 Book of Standards Volume: 04.09 ASTM D60231. Scope 1.1 This test method explains determination of the density (Note 1) of freshly mixed Controlled Low-Strength Material (CLSM) and gives formulas for calculating the yield, cement content, and the air content of the CLSM. This test method is based on Test Method C 138 for Concrete. Note 1- Unit Weight was the previous terminology used to describe the property determined by this test method, which is mass per unit volume. 1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026. 1.2.1 The method used to specify how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope. 1.3 The values stated in SI units are to be regarded as standard. The inch-pound equivalents are shown for information only. 1.4 CLSM is also known as flowable fill, controlled density fill, soil-cement slurry, soil-cement grout, unshrinkable fill, 'K-Krete,' and other similar names. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ( Warning: Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)
ASTM Standards C29/C29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate C125 Terminology Relating to Concrete and Concrete Aggregates C128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete C150 Specification for Portland Cement C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method D653 Terminology Relating to Soil, Rock, and Contained Fluids D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction D4832 Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders D5971 Practice for Sampling Freshly Mixed Controlled Low-Strength Material D6024 Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application D6026 Practice for Using Significant Digits in Geotechnical Data D6103 Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) Keywords air content; backfill; cement content; CLSM; construction control; density; flowable fill; mix design; quality control; relative yield; soil stabilization; unit weight; yield; ICS Code ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar) DOI: 10.1520/D6023-07 ASTM International is a member of CrossRef. ASTM D6023The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|