ASTM D5144-08
Historical Standard: ASTM D5144-08 Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants
SUPERSEDED (see Active link, below)
ASTM D5144
1. Scope
1.1 This guide provides a common basis on which protective coatings for the surfaces of nuclear power generating facilities may be qualified and selected by reproducible evaluation tests. This guide also provides guidance for application and maintenance of protective coatings. Under the environmental operating and accident conditions of nuclear power generation facilities, encompassing pressurized water reactors (PWRs) and boiling water reactors (BWRs), coating performance may be affected by exposure to any one, all, or a combination of the following conditions: ionizing radiation; contamination by radioactive nuclides and subsequent decontamination processes; chemical and water sprays; high-temperature high-pressure steam; and abrasion or wear.
1.2 The content of this guide includes:
Section | |
Referenced Documents | 2 |
Terminology | 3 |
Significance and Use | 4 |
Coating Material Testing | 5 |
Thermal Conductivity | 5 |
Surface Preparation, Coating Application, and Inspection for Shop and Field Work |
6 |
Quality Assurance | 7 |
Keywords | 8 |
1.2.1 In addition, this guide addresses technical topics within ANSI N5.12 and ANSI N101.2 that are covered by separate ASTM standards, for example, surface preparation, (shop and field) and coating application, (shop and field).
1.2.2 Applicable sections of this guide and specific acceptance criteria may be incorporated into specifications and other documents where appropriate.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
D3843 Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
D3911 Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
D3912 Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants
D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
D4082 Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants
D4227 Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces
D4228 Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces
D4537 Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in Nuclear Facilities
D4538 Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D5139 Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
D5163 Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
D7167 Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
D7230 Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
D7234 Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
D7491 Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants
E84 Test Method for Surface Burning Characteristics of Building Materials
E684 Practice for Approximate Determination of Current Density of Large-Diameter Ion Beams for Sputter Depth Profiling of Solid Surfaces
E1461 Test Method for Thermal Diffusivity by the Flash Method
E1530 Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
Keywords
ANSI replacement standards; decontamination; Design Basis Accident (DBA); nuclear power plants; protective coating standards; qualification testing; quality assurance Coating Service Level I, Coating Service Level II, and Coating Service Level III; radiation; safety related; Contamination--paints/coatings applications; Nuclear reactor vessels--coatings applications; Qualifications--nuclear facilities; Quality assurance (QA)--coatings/linings; Testing methods--paints/related coatings; ANSI replacement standards; Coatings (nuclear facilities); DBA (design basis accident); Decontamination; Protective coatings; Radiation exposure; Service Level I and/or II;
ICS Code
ICS Number Code 27.120.10 (Reactor engineering)
DOI: 10.1520/D5144-08
ASTM International is a member of CrossRef.