FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-B697 2010ASTM B697 - 88(2010)Standard Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic CoatingsActive Standard ASTM B697 | Developed by Subcommittee: B08.10 Book of Standards Volume: 02.05 ASTM B697Abstract This guide covers the standard method for selecting sampling plans to be used in the inspection of electrodeposited metallic and inorganic coatings on products for the purpose of deciding whether submitted lots comply with the specifications applicable to the coatings. The characteristics of the sampling plan are expressed in terms of the Acceptable Quality Level (AQL), Limiting Quality Level (LQL), Average Outgoing Quality (AOQ), and Average Outgoing Quality Limit (AOQL). General procedures and criteria for the construction and selection of the type of sampling plan, selection of a specific plan, selection of the inspection lot, sampling and inspection of samples, and the disposition of lots are discussed fully. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This guide gives guidance in the selection of sampling plans to be used in the inspection of electrodeposited and related coatings on products for the purpose of deciding whether submitted lots of coated products comply with the specifications applicable to the coatings. This supplements Test Method B602 by giving more information on sampling inspection and by providing additional sampling plans for the user who finds the limited choice of plans in Test Method B602 to be inadequate. 1.2 When using a sampling plan, a relatively small part of the articles in an inspection lot is selected and inspected. Based on the results, a decision is made that the inspection lot either does or does not satisfactorily conform to the specification. 1.3 This guide also contains several sampling plans. The plans are attribute plans, that is, in the application of the plans each inspected article is classified as either conforming or nonconforming to each of the coating requirements. The number of nonconforming articles is compared to a maximum allowable number. The plans are simple and relatively few. Additional plans and more complex plans that cover more situations are given in the Refs (1-7) at the end of this guide and in MIL-STD-105. 1.4 Acceptance sampling plans are used: 1.4.1 When the cost of inspection is high and the consequences of accepting a nonconforming article are not serious. 1.4.2 When 100 % inspection is fatiguing and boring and, therefore, likely to result in errors. In these cases a sampling plan may provide greater protection than 100 % inspection. 1.4.3 When inspection requires a destructive test. Here, sampling inspection must be used. 1.5 Another general type of acceptance sampling plan that is not covered in these guidelines is the variables plan in which measured values of characteristics are analyzed by statistical procedures. Such plans, when applicable, can reduce inspection cost and increase quality protection. Information on variables plans is given in Test Method B762 , MIL-STD-414, ANSI/ASQC Z1.9-1979, and Refs (1-2) .
ASTM Standards B602 Test Method for Attribute Sampling of Metallic and Inorganic Coatings B762 Test Method of Variables Sampling of Metallic and Inorganic Coatings ANSI Standard ANSI/ASQCZ1.9-1979 Sampling Procedures and Tables for Inspection by Variables for Percent NonconformanceMilitary Standards MIL-STD-414 Sampling Procedures and Tables for Inspection by Variables for Percent DefectiveKeywords Acceptance criteria/testing--coatings; AOQL (average outgoing quality limit)--sampling plans; Electrodeposited coatings; Inorganic coatings; Inspection; LQL sampling plan; Metallic coatings; Quality control (QC)--paints/related coatings/materials; Quality control (QC)--metals; Sampling electrodeposited coatings; ICS Code ICS Number Code 25.220.40 (Metallic coatings) DOI: 10.1520/B0697-88R10 ASTM International is a member of CrossRef. ASTM B697This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|