ASTM-A1031/A1031M, 2017

ASTM

A1031/A1031M-12(2017) Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled

Edition: 2017

$78.62
Unlimited Users per year

Description
Subscription Info
Packages
About ASTM

Description of ASTM-A1031/A1031M 2017

ASTM A1031/A1031M-12-Reapproved2017

Active Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled

ASTM A1031/A1031M

Scope

1.1 This specification covers hot-rolled, heavy thickness coils beyond the size limits of Specifications A506 and A507.

1.2 The product is available in three designations: Alloy Steel, Drawing Steel, and Structural Alloy Steel.

1.3 Alloy steel is furnished to chemical composition requirements and is intended primarily for general or miscellaneous use where bending and moderate forming is a requirement.

1.4 Drawing steel is produced principally for applications involving severe cold plastic deformation such as deep drawn or severely formed parts.

1.4.1 Drawing steel may be furnished in several conditions, heat treatments, surface finishes, and edges, as specified herein.

1.5 Structural steel is furnished to chemical composition requirements and to specific mechanical property requirements which may include tension tests, hardness tests, or other commonly accepted mechanical tests.

1.5.1 The formability of structural steel decreases with increasing yield strength or hardness. Therefore, product design in relation to the mechanical properties of the grade used must be considered.

1.6 This material is available only in coils described as follows:

Product	Size Limits, Coils Only
Product	Width, in. [mm]	Thickness, in. [mm]
Strip	Over 8 to 12, incl	0.230 to 1.000, incl
	[Over 200 to 300]	[Over 6.0 to 25]
Sheet	Over 12	0.230 to 1.000, incl
	[Over 300]	[from 6.0 through 25]

1.7 Sheet and strip in coils of sizes noted in 1.6 are covered by this specification only with the following provisions:

1.7.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils). A plate produced in this manner is no longer governed by this sheet steel specification and since this material is now plate, the appropriate plate standard must now apply.

1.7.2 The dimensional tolerances of Specification A635/A635M are applicable to material produced to this specification.

1.7.3 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming.

1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

TABLE 1 Standard Steels Commonly Produced for Alloy Steel Sheet and Strip

Steel Designation No.	Chemical Composition Ranges and Limits, % (Heat Analysis)^A
Steel Designation No.	C	Mn	P	S	Si^B	Ni	Cr	Mo	V
E3310^C	0.08-0.13	0.45-0.60	0.025	0.025	0.15-0.30	3.25-3.75	1.40-1.75	. . .	. . .
4012^C	0.09-0.14	0.75-1.00	0.025	0.025	0.15-0.30	. . .	. . .	0.15-0.25	. . .
4118	0.18-0.23	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.40-0.60	0.08-0.15	. . .
4130	0.28–0.33	0.40–0.60	0.025	0.025	0.15-0.30	. . .	0.80–1.10	015–0.25	. . .
4135	0.33-0.38	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4137	0.35-0.40	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4140	0.38–0.43	0.75–1.00	0.025	0.025	0.15-0.30	. . .	0.80–1.10	0.15-0.25	. . .
4142	0.40-0.45	0.75-1.00	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4145	0.43-0.48	0.75-1.00	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4147^C	0.45-0.50	0.75-1.00	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4150	0.48-0.53	0.75-1.00	0.025	0.025	0.15-0.30	. . .	0.80-1.10	0.15-0.25	. . .
4320	0.17-0.22	0.45-0.65	0.025	0.025	0.15-0.30	1.65-2.00	0.40-0.60	0.20-0.30	. . .
4340	0.38–0.43	0.60–0.80	0.025	0.025	0.15-0.30	1.65-2.00	0.70–0.90	0.20-0.30	. . .
E4340	0.38-0.43	0.65-0.85	0.025	0.025	0.15-0.30	1.65-2.00	0.70-0.90	0.20-0.30	. . .
4520^C	0.18-0.23	0.45-0.65	0.025	0.025	0.15-0.30	. . .	. . .	0.45-0.60	. . .
4615	0.13-0.18	0.45-0.65	0.025	0.025	0.15-0.30	1.65-2.00	. . .	0.20-0.30	. . .
4620	0.17-0.22	0.45-0.65	0.025	0.025	0.15-0.30	1.65-2.00	. . .	0.20-0.30	. . .
4718	0.16-0.21	0.70-0.90	0.025	0.025	0.15-0.30	0.90-1.20	0.35-0.55	0.30-0.40	. . .
4815	0.13-0.18	0.40-0.60	0.025	0.025	0.15-0.30	3.25-3.75	. . .	0.20-0.30	. . .
4820	0.18-0.23	0.50-0.70	0.025	0.025	0.15-0.30	3.25-3.75	. . .	0.20-0.30	. . .
5015	0.12-0.17	0.30-0.50	0.025	0.025	0.15-0.30	. . .	0.30-0.50	. . .	. . .
5046	0.43-0.50	0.75-1.00	0.025	0.025	0.15-0.30	. . .	0.20-0.35	. . .	. . .
5115	0.13-0.18	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.70-0.90	. . .	. . .
5120	0.17–0.22	0.70–0.90	0.025	0.025	0.15-0.30	. . .	0.70–0.90	. . .	. . .
5130	0.28–0.33	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.80-1.10	. . .	. . .
5132	0.30–0.35	0.60-0.80	0.025	0.025	0.15-0.30	. . .	0.75-1.00	. . .	. . .
5140	0.38–0.43	0.70–0.90	0.025	0.025	0.15-0.30	. . .	0.70–0.90	. . .	. . .
5150	0.48–0.53	0.70–0.90	0.025	0.025	0.15-0.30	. . .	0.70–0.90	. . .	. . .
5160	0.56–0.64	0.75–1.00	0.025	0.025	0.15-0.30	. . .	0.70–0.90	. . .	. . .
E51100^C	0.95–1.10	0.25-0.45	0.025	0.025	0.15-0.30	. . .	0.90-1.15	. . .	. . .
E52100	0.98–1.10	0.25-0.45	0.025	0.025	0.15-0.30	. . .	1.30-1.60	. . .	. . .
6150	0.48–0.53	0.70-0.90	0.025	0.025	0.15-0.30	. . .	0.80-1.10	. . .	0.15 min
6158^C	0.55–0.62	0.70–1.10	0.025	0.025	0.15-0.30	. . .	0.90–1.20	. . .	0.10–0.20
8615	0.13–0.18	0.70–0.90	0.025	0.025	0.15-0.30	0.40–0.70	0.40–0.60	0.15–0.25	. . .
8617	0.15–0.20	0.70-0.90	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8620	0.18–0.23	0.70–0.90	0.035	0.035	0.15-0.30	0.40-0.70	0.40–0.60	0.15–.025	. . .
8630	0.28–0.33	0.70-0.90	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8640	0.38–0.43	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8642^C	0.40-0.45	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8645	0.43-0.48	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8650^C	0.48-0.53	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8655	0.501-0.59	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8660	0.55-0.65	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.15-0.25	. . .
8720	0.18-0.23	0.70-0.90	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.20-0.30	. . .
8735^C	0.33-0.38	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.20-0.30	. . .
8740^C	0.38-0.43	0.75-1.00	0.025	0.025	0.15-0.30	0.40-0.70	0.40-0.60	0.20-0.30	. . .
9260	0.56-0.64	0.75-1.00	0.025	0.025	1.80-2.20	. . .	. . .	. . .	. . .
9262^C	0.55-0.65	0.75-1.00	0.025	0.025	1.80-2.20	. .	0.25-0.40	. . .	. . .
E9310^C	0.08-0.13	0.45-0.65	0.025	0.025	0.20-0.35	3.30-35.0	1.00-1.40	0.08-0.15	. . .

(A) The chemical ranges and limits shown are subject to product analysis tolerances. See Specification A505.

(B) Other silicon ranges are available. Consult the producer.

1.8.1 Within the text the SI units are shown in brackets.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

alloy steel sheet; alloy steel strip; alloy structural steel; drawing steel; heavy-thickness coils; hot-rolled alloy steel;

ICS Code

ICS Number Code 77.140.50 (Flat steel products and semi-products)

DOI: 10.1520/A1031_A1031M-12R17

This book also exists in the following packages...

Year	Publisher	Title		Annual Price
VAR	ASTM	ASTM Section 1 - Iron and Steel Products	[+]	$5,898.91	Buy
	2000	ASTM	A1003/A1003M-00 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2001	ASTM	A1003/A1003M-01 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2002	ASTM	A1003/A1003M-02 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2002	ASTM	A1003/A1003M-02a Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2005	ASTM	A1003/A1003M-05 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2008	ASTM	A1003/A1003M-08 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members
	2000	ASTM	A1008/A1008M-00 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2001	ASTM	A1008/A1008M-01a Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2002	ASTM	A1008/A1008M-02 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2003	ASTM	A1008/A1008M-03 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
			Showing 10 of 8640+ books in package. Click here to download full list of books.
VAR	ASTM	ASTM Volume 01.03 Steel--Plate, Sheet, Strip, Wire; Stainless Steel Bar	[+]	$896.68	Buy
	2000	ASTM	A1008/A1008M-00 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2001	ASTM	A1008/A1008M-01a Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2002	ASTM	A1008/A1008M-02 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2003	ASTM	A1008/A1008M-03 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2004	ASTM	A1008/A1008M-04 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2004	ASTM	A1008/A1008M-04a Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2004	ASTM	A1008/A1008M-04b Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
	2005	ASTM	A1008/A1008M-05 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
	2005	ASTM	A1008/A1008M-05a Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
	2005	ASTM	A1008/A1008M-05b Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
			Showing 10 of 1020+ books in package. Click here to download full list of books.

Subscription Information

MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

Some features of MADCAD.com ASTM Standards Subscriptions are:

- Online access: With MADCAD.com’ s web based subscription service no downloads or installations are required. Access ASTM Standards from any browser on your computer, tablet or smart phone.

- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.

For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

About ASTM

ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.

Email *
Password *
Confirm *
First Name *
Last Name *
Title
Company Name *
Company Size *
Industry *
Address *
Address 2
City *
State *	Zip *
Country *
Phone *
How did you hear about MADCAD.com? *

Company*
Full name*
Email*
Phone

Full name*
Email*
Phone
Your selection

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

To continue with accurate pricing,
please select your company type below:

We need your input!

Cart Warning

Description of ASTM-A1031/A1031M 2017

ASTM A1031/A1031M-12-Reapproved2017

Active Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled

ASTM A1031/A1031M

This book also exists in the following packages...

Subscription Information

About ASTM

Username:
Password:

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

To continue with accurate pricing, please select your company type below:

We need your input!

Cart Warning

Description of ASTM-A1031/A1031M 2017

ASTM A1031/A1031M-12-Reapproved2017

Active Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled

ASTM A1031/A1031M

This book also exists in the following packages...

Subscription Information

About ASTM

To continue with accurate pricing,
please select your company type below: