FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D204 2010ASTM D204 - 02(2010)e1Standard Test Methods for Sewing ThreadsActive Standard ASTM D204 | Developed by Subcommittee: D13.58 Book of Standards Volume: 07.01 ASTM D204Significance and Use Acceptance Testing The test methods in Test Methods D204 for the determination of the properties of sewing thread are considered satisfactory for acceptance testing of commercial shipments of sewing thread, unless specified in the individual test method. These test methods are the best available and are used extensively in the trade. If there are differences of practical significance between reported test results for two laboratories (or more) comparative test should be performed to determine if there is a statistical bias between them using competent statistical assistance. As a minimum, use the samples for such a comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. 1. Scope 1.1 These test methods can be used to evaluate sewing threads of any fiber. 1.1.1 The test methods in this standard are intended to evaluate only sewing thread taken from thread holders. 1.2 These test methods only provide for the measurement of sewing thread physical properties. These test methods do not address any other properties that may be important for the satisfactory performance of sewing threads under particular end use conditions.
ASTM Standards D76 Specification for Tensile Testing Machines for Textiles D123 Terminology Relating to Textiles D1422 Test Method for Twist in Single Spun Yarns by the Untwist-Retwist Method D1423 Test Method for Twist in Yarns by Direct-Counting D1683 Test Method for Failure in Sewn Seams of Woven Apparel Fabrics D1776 Practice for Conditioning and Testing Textiles D1777 Test Method for Thickness of Textile Materials D1907 Test Method for Linear Density of Yarn (Yarn Number) by the Skein Method D2256 Test Method for Tensile Properties of Yarns by the Single-Strand Method D2258 Practice for Sampling Yarn for Testing D2724 Test Methods for Bonded, Fused, and Laminated Apparel Fabrics D3693 Specification for Labeled Length per Holder of Sewing Thread D3823 Practice for Determining Ticket Numbers for Sewing Threads D3940 Test Method for Bursting Strength (Load) and Elongation of Sewn Seams of Knit or Woven Stretch Textile Fabrics D4848 Terminology Related to Force, Deformation and Related Properties of Textiles D4849 Terminology Related to Yarns and Fibers D6193 Practice for Stitches and Seams AATCC Standards EvaluationProcedure3 Chromatic Transference ScaleKeywords breaking strength; strand; colorfastness; diameter; dimensional change; length; sewing thread; textile strand; twist; twist balance; yarn number; Yarn number; Breaking strength/tenacity--textile fabrics/fibers; Colorfastness; Diameter--textile fabrics/fibers; Dimensional change; Fiber length; Sewing thread; Shrinkage--textile fabrics/fibers; Textile fibers; Twist--textiles; Twist balance ; ICS Code ICS Number Code 59.080.20 (Yarns) DOI: 10.1520/D0204-02R10E01 ASTM International is a member of CrossRef. ASTM D204This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|