FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-F2162 2008ASTM F2162 - 01(2008)Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard TypeActive Standard ASTM F2162 | Developed by Subcommittee: F34.04 Book of Standards Volume: 01.08 ASTM F2162Abstract This specification covers the requirements for standard-type needle roller bearings with drawn outer rings, full complement, without inner rings, and with either open (Type B) or closed ends (Type M). Materials covered by this specification are needle rollers which shall be manufactured from steel, alloy, or carbon, and shall be of Grade E50100 or E52100. Rings, on the other hand, shall be manufactured from steel, alloy, or carbon, with carburizing grade 4620, 4720, 8620, 8720, or 1010-1020. Needle rollers and rings shall be hardened by heat treatment, and bearings shall be coated with rust preventive film. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers standard-type needle roller bearings having drawn outer rings, full complement, without inner rings, with either open or closed ends. 1.2 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged. 1.3 The inner rings specified in this specification are not intended for use in flight critical systems of aircraft. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Note 1This specification contains many of the requirements of MS17131, which was originally developed by the Department of Defense and is currently maintained by the Defense Supply Center Richmond.
ASME Standard ASMEB46.1 Surface Texture Surface Roughness, Waviness, and Lay Available from Global Engineering Documents, 15 Inverness Way, East Englewood, CO 80112-5704, http://www.global.ihs.com.SAE Standard SAEJ-404 Chemical Composition of SAE Alloy Steels Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.Military Standard MIL-STD-130 Identification Marking of US Military Property Available from USA Information Systems, 1092 Laskin Rd., Ste. 208, Virginia Beach, VA 23451.American Bearing Manufacturers Association (ABMA) Standard STD4 Tolerance Definitions and Gauging Practices For Ball and Roller Bearings Available from the American Bearing Manufacturers Association, 1200 19th St. NW, Ste. 300, Washington, DC 20036-2401.ISO Standards ISO1132 Rolling Bearings--Tolerances--DefinitionsASTM Standards E18 Test Methods for Rockwell Hardness of Metallic Materials E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness E384 Test Method for Knoop and Vickers Hardness of Materials F2163 Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring Keywords drawn outer ring; full complement bearing; needle bearing; MS17131; roller bearing; Ball/roller bearings--specifications; Basic dynamic load rating; Basic static load rating; Drawn outer ring; Full complement bearing; Inner ring; Needle bearing; Needle roller bearing; Roller bearings; ICS Code ICS Number Code 21.100.20 (Rolling bearings) DOI: 10.1520/F2162-01R08 ASTM International is a member of CrossRef. ASTM F2162This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|