ASTM F1760-01(2005)e1
Historical Standard: ASTM F1760-01(2005)e1 Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
SUPERSEDED (see Active link, below)
ASTM F1760
1. Scope
1.1 This specification has been published in response to the special circumstance of regulatory requirements regarding federal procurement guidelines for plastic pipe having recycled content.
1.2 This specification covers coextruded Poly(Vinyl Chloride) (PVC) plastic pipe with a center layer and concentric inner and outer solid layers. The pipe is produced using a multi-layer coextrusion die. The inner and outer layers are made of virgin PVC compound and the center layer has reprocessed-recycled PVC content. The pipe is for non-pressure use in three series:
1.2.1 Sewer-Drain series with a sewer-pipe outside diameter and a pipe stiffness of 46 psi (320 kPa),
1.2.2 IPS Schedule 40 series, and
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of 100 psi (690 kPa) and 120 psi (830 kPa).
1.3 Pipe that is outside-diameter controlled does not necessarily have an inside diameter suitable for use as a fitting socket.
1.4 All series may be perforated.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI values are provided for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D883 Terminology Relating to Plastics
D1243 Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2466 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F512 Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation
F1336 Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
F1365 Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
Plastic Pipe Institute Technical Report
PPI-TR-7 Recommended Method for Calculation of Nominal Weight of Plastic PipeKeywords
coextruded pipe; PVC plastic pipe; recycled plastic material; reprocessable plastic material; Reprocessed-recycled content; Coextruded poly(vinyl chloride)(PVC) pipe/tube--specifications; Nonpressure piping--specifications; Poly(vinyl chloride)(PVC) pipe--specifications;
ICS Code
ICS Number Code 23.040.20 (Plastic pipes)
DOI: 10.1520/F1760-01R05E01
ASTM International is a member of CrossRef.