ASTM E2355-04
Historical Standard: ASTM E2355-04 Standard Test Method for Measuring the Uniformity of an Absorptive Electrochromic Coating on a Glazing Surface
SUPERSEDED (see Active link, below)
ASTM E2355
1. Scope
1.1 The test described is a method for measuring the uniformity of an absorptive electrochromic coating (ECC) in a static colored or bleached state on a glazing surface, which will ultimately be one of two or more glazings in a preassembled permanently sealed insulating glass unit (IGU). Cross sections of typical electrochromic windows (ECWs) have three to five-layers of coatings that include one to three active layers sandwiched between two transparent conducting electrodes (TCEs, see Section ). Examples of the cross-sectional arrangements can be found in 'Evaluation Criteria and Test Methods for Electrochromic Windows.' (For a list of acronyms used in this Standard, see , Section ).
1.2 The test method is applicable only for layered (one or more active coatings between the TCEs) absorptive ECCs on vision glass (superstrate and substrate) areas planned for use in IGUs for buildings, such as glass doors, windows, skylights, and exterior wall systems. The layers used for electrochromically changing the optical properties may be inorganic or organic materials between the superstrate and substrate and may include laminates.
1.3 The ECCs used in this test method will ultimately be exposed (Test Method E 2141) to solar radiation and deployed to control the amount of radiation by absorption and reflection and thus, limit the solar heat gain and amount of solar radiation that is transmitted into the building.
1.4 The test method is not applicable to other types of coatings on vision glass with other chromogenic coatings that cannot be held in a static colored or bleached state.
1.5 The test method is not applicable to IGUs that will be constructed from superstrate or substrate materials other than glass.
1.6 The test method is not applicable for measuring the uniformity of ECC coatings during the coloring or bleaching processes.
1.7 The test method referenced herein is a laboratory test conducted under specified conditions. This test method is intended for use in assessing the changes in uniformity of an ECC on vision glass, which will be incorporated into an IGU and subjected to a series of tests for assessing the durability of the coating or the IGU unit, or both.
1.8 The values stated in metric (SI) units are to be regarded as the standard.
1.9 There is no comparable International Standards Organization Standard.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C168 Terminology Relating to Thermal Insulation
C1048 Specification for Heat-Strengthened and Fully Tempered Flat Glass
E2141 Test Methods for Assessing the Durability of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
E2188 Test Method for Insulating Glass Unit Performance
E2189 Test Method for Testing Resistance to Fogging in Insulating Glass Units
E2190 Specification for Insulating Glass Unit Performance and Evaluation
E2240 Test Method for Assessing the Current-Voltage Cycling Stability at 90C (194F) of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
E2241 Test Method for Assessing the Current-Voltage Cycling Stability at Room Temperature of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
Keywords
chromogenic glazing; durability; electrochromic windows; fenestration; insulating glass units; sealed insulating glass units; Chromogenic glazings; Coatings (electrochromic); Electrochromic windows (ECW); Glazing surface; Insulating glass (IG); Sealed insulating glass units; Transparent conducting electrodes ;
ICS Code
ICS Number Code 25.220.40 (Metallic coatings)
DOI: 10.1520/E2355-04
ASTM International is a member of CrossRef.