ASTM D7230-06
Historical Standard: ASTM D7230-06 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
SUPERSEDED (see Active link, below)
ASTM D7230
1. Scope
1.1 This guide establishes procedures for evaluating lining system test specimens under simulated operating conditions.
1.2 Lining systems to be tested in accordance with this guide are intended for use in both new construction and for refurbishing existing systems or components.
1.3 The lining systems evaluated in accordance with this guide are expected to be applied to metal substrates comprising water-wetted (that is, continuous or intermittent immersion) surfaces in systems that may include:
1.3.1 Service water piping upstream of safety-related components,
1.3.2 Service water pump internals (draft tube, volutes, and diffusers),
1.3.3 Service water heat exchanger channels, pass partitions, tubesheets, end bells, and covers,
1.3.4 Service water strainers, and
1.3.5 Refueling water storage tanks and refuel cavity water storage tanks.
1.4 This guide anticipates that the lining systems to be tested include liquid-grade and paste-grade polymeric materials. Sheet type lining materials, such as rubber, are excluded from the scope of this guide.
1.5 Because of the specialized nature of these tests and the desire in many cases to simulate to some degree the expected service environment, the creation of a standard practice is not practical. This standard gives guidance in setting up tests and specifies test procedures and reporting requirements that can be followed even with differing materials, specimen preparation methods, and test facilities.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A36/A36M Specification for Carbon Structural Steel
C868 Test Method for Chemical Resistance of Protective Linings
D115 Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
D714 Test Method for Evaluating Degree of Blistering of Paints
D2240 Test Method for Rubber Property--Durometer Hardness
D2583 Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
D2794 Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
D4082 Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants
D4538 Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D5139 Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
D5144 Guide for Use of Protective Coating Standards in Nuclear Power Plants
D6677 Test Method for Evaluating Adhesion by Knife
D7167 Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
E96/E96M Test Methods for Water Vapor Transmission of Materials
G14 Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
G42 Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures
NACE International
TM0404 Offshore Platform Atmospheric and Splash Zone New Construction Coating System EvaluationFederal Standards
EPAMethod415.1 Total Organic Carbon in WaterKeywords
Coating Service Level III; CSL III; cold-wall effect; lining systems; metal substrates; nuclear; polymeric material; safety-related service water; service water systems;
ICS Code
ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)
DOI: 10.1520/D7230-06
ASTM International is a member of CrossRef.