FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D4799 2008 Significance and Use
This weathering apparatus is used for comparing the weathering characteristics of bituminous materials against a control material for which the outdoor weathering characteristics are known. It is not possible to establish a precise correlation between accelerated and natural weathering because ( 1 ) there are geographical climatic variations, local weather variations, and variations in local pollutants, and ( 2 ) the relation between accelerated and natural weathering is material dependent. Acceleration factors differ between materials as well as between formulations of the same material. Guide G 141 provides guidance regarding this issue. Note 1—This practice can be used for other than bituminous materials, but the significance and use have not been evaluated. 1. Scope 1.1 This practice describes test conditions and procedures for fluorescent UV and condensation exposures conducted according to Practices G 151 and G 154 for bituminous roofing and waterproofing materials that have a minimum softening point of approximately 95 ° C (200 ° F) as determined by Test Method D 36. (Also see Terminology G 113.) 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)D1669 Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings D1670 Test Method for Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials G113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials G141 Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials G147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials Keywords accelerated weathering; bituminous materials; degradation; exposure; fluorescent UV and condensation; light exposure; roofing; ultraviolet; waterproofing; Fluorescent UV-light apparatus; Light exposure; Ultraviolet (UV) analysis; Accelerated aging/testing--building materials; Accelerated weathering; Bituminous roofing materials; Exposure tests--fluorescent-UV apparatus; ICS Code ICS Number Code 75.140 (Waxes, bituminous materials and other petroleum products); 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials) DOI: 10.1520/D4799-08 ASTM International is a member of CrossRef. The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|