FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D3154 2006ASTM D3154 - 00(2006)Standard Test Method for Average Velocity in a Duct (Pitot Tube Method)Active Standard ASTM D3154 | Developed by Subcommittee: D22.03 Book of Standards Volume: 11.07 ASTM D3154Significance and Use The procedures presented in this test method are available, in part, in Test Method D 3685 /D 3685M, as well as the ASME Methods given in 2.3 and Footnote 8, 5 the CFR given in 2.4 , and the publication given in Footnote 9. 6 1. Scope 1.1 This test method describes measurement of the average velocity of a gas stream for the purpose of determining gas flow in a stack, duct, or flue. Although technically complex, it is generally considered the most accurate and often the only practical test method for taking velocity measurements. 1.2 This test method is suitable for measuring gas velocities above 3 m/s (10 ft/s). 1.3 This test method provides procedures for determining stack gas composition and moisture content. 1.4 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only. 1.5 This test method is applicable to conditions where steady-state flow occurs, and for constant fluid conditions. If these conditions are not meant, other methods must be used. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D1071 Test Methods for Volumetric Measurement of Gaseous Fuel Samples D1193 Specification for Reagent Water D1356 Terminology Relating to Sampling and Analysis of Atmospheres D3195 Practice for Rotameter Calibration D3631 Test Methods for Measuring Surface Atmospheric Pressure D3685/D3685M Test Methods for Sampling and Determination of Particulate Matter in Stack Gases D3796 Practice for Calibration of Type S Pitot Tubes E1 Specification for ASTM Liquid-in-Glass Thermometers E337 Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) EPA Standards EPA-600/4-77-027b Quality Assurance Handbook for Air Pollution Measurement Systems. Vol. III. Stationary Source Specific MethodsASME Standards ASMEPerformanceTestC Determining the Concentration of Particulate Matter in a Gas StreamCode of Federal Regulation CFRPart50 Standards of Performance for Stationary Sources, Appendix A; Test Methods 1 through 4Keywords stack gas velocity; pitot traverse; pitot tube; Staubscheibe pitot tube; Type S pitot tube; Orsat; Orsat analyzer; Method 1; Method 2; Method 3; Method 4; stack gas moisture; stack gas molecular weight; stack gas density; ICS Code ICS Number Code 17.120.20 (Flow in open channels) DOI: 10.1520/D3154-00R06 ASTM International is a member of CrossRef. ASTM D3154This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|