ASTM D2969-04
Historical Standard: ASTM D2969-04 Standard Test Methods for Steel Tire Cords
SUPERSEDED (see Active link, below)
Translated Standard: Russian
more info
ASTM D2969
1. Scope
1.1 These test methods cover the testing of cords made from steel that are specifically designed for use in the reinforcement of pneumatic tires. By agreement, these test methods may be used to test similar cords or filaments used for reinforcing other rubber products. The steel cords may be wound on spools or beams. The steel cords may also be woven into fabric, in which case they must be removed from the fabric prior to testing.
Note 1For other methods of testing tire cords and tire cord fabrics, refer to Methods D 885, Test Methods D 1871, Specifications D 122, and Test Methods D 2692 and D 2970. For tolerances on tire cords and tire cord fabrics, refer to Specifications D 122 and Methods D 885.
1.2 These test methods include test procedures only; they do not establish specifications or tolerances.
1.3 This test method includes the following sections:
Subject | Section |
Adhesion of Steel Cords and Filaments to Elastomers | |
Brass Coating Composition and Mass | , |
Breaking Force (Strength) | |
Construction | |
Data Form for Reporting Test Results | |
Elongation at Break | |
Elongation Between Defined Forces (EDF) | |
Flare | |
Lay | |
Linear Density | |
Visual Appearance | |
Nomenclature System | |
Residual Torsions | |
Straightness | |
Thickness and Out-of-Roundness |
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See and Note 0.
1.4 This standard is written in SI units. No other units of measurement are included in this standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D76 Specification for Tensile Testing Machines for Textiles
D122 Tolerances for Tire Fabrics Other Than Tire Cord Fabrics
D123 Terminology Relating to Textiles
D885 Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns Made from Manufactured Organic-Base Fibers
D1871 Test Method for Adhesion Between Tire Bead Wire and Rubber
D2229 Test Method for Adhesion Between Steel Tire Cords and Rubber
D2692 Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
D2904 Practice for Interlaboratory Testing of a Textile Test Method that Produces Normally Distributed Data
D2970/D2970M Test Methods for Testing Tire Cords, Tire Cord Fabrics, and Industrial Yarns Made From Glass Filaments
D4393 Test Method for Strap Peel Adhesion of Reinforcing Cords or Fabrics to Rubber Compounds
D6477 Terminology Relating to Tire Cord, Bead Wire, Hose Reinforcing Wire, and Fabrics
E663 Practice for Flame Atomic Absorption Analysis
Keywords
adhesion; brass coating; direction of lay; elongation; linear density; steel cord; strength, breaking; thickness; visual appearance; Stiffness--textile materials/applications; Tensile properties/testing--textile materials/applications; Thickness--textile fabrics/fibers; Tire cords and tire cord fabrics; Visual examination--textiles; Zinc content; Adhesion; Brass electrodeposition; Breaking strength/tenacity--textile fabrics/fibers; Copper content--steel; Density--linear; Elongation--textiles; Rubber adhesion; Steel cords; Steel wire strand;
ICS Code
ICS Number Code 77.140.65 (Steel wire, wir ropes and link chains); 83.160.01 (Tyres in general)
DOI: 10.1520/D2969-04
ASTM International is a member of CrossRef.