ASTM C844-99
Historical Standard: ASTM C844-99 Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
SUPERSEDED (see Active link, below)
ASTM C844
1. Scope
1.1 This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters.
Note 1-Gypsum veneer base shall not be used as a base for direct adhesive application of ceramic, metal, or plastic tile in areas exposed to abnormal moisture or humidity or temperature.1.2 Where a specific degree of fire resistance is required for gypsum base and veneer plaster systems, a special resistant base may be required. Details of constructions to achieve the required fire resistance may be obtained from official reports of fire tests conducted at recognized fire testing laboratories in accordance with Test Methods E119.
1.3 Where a specific degree of sound control is required for veneer plaster assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized sound testing laboratories in accordance with the applicable sound tests, Test Method C423, Test Method E90, or Test Method E492.
1.4 Where this specification is more stringent (size or thickness of framing; spacing of fasteners) than the fire-rated construction, this specification shall govern; otherwise, the construction described in the fire test report shall govern.
1.5 Unheated spaces above gypsum veneer base ceilings shall be properly ventilated (see Appendix X3).
1.6 General Information -The Appendixes give general information and also suggestions for inclusions to be made elsewhere by the specifier and are not a part of this specification. The work shall be properly coordinated with the work of other trades.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C423 Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C514 Specification for Nails for the Application of Gypsum Board
C587 Specification for Gypsum Veneer Plaster
C588/C588M Specification for Gypsum Base for Veneer Plasters
C754 Specification for Installation of Steel Framing Members to Receive Screw-Attached Gypsum Panel Products
C954 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
C955 Specification for Load-Bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases
C1002 Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
C1007 Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
C1047 Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
C1546 Guide for Installation of Gypsum Products in Concealed Radiant Ceiling Heating Systems
E90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E492 Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
American Softwood Lumber Standard
PS20 American Softwood Lumber Standard Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.Keywords
electric heat cable; gypsum; gypsum base; veneer plastic; Gypsum plaster--specifications; Installation--gypsum products; Plaster--specifications;
ICS Code
ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
DOI: 10.1520/C0844-99
ASTM International is a member of CrossRef.
