FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-C1480 2012ASTM C1480 / C1480M - 07(2012)Standard Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete ApplicationActive Standard ASTM C1480 / C1480M | Developed by Subcommittee: C09.46 Book of Standards Volume: 04.02 ASTM C1480 / C1480MAbstract This specification covers laboratory performance standards for pre-blended, dry, packaged, combined materials for use in wet or dry shortcrete applications. Dry packaged shortcrete materials are categorized as to type and grade. Basic materials shall meet the requirements of this specification. Additional materials shall be permitted only if adequate test data are available to insure that the ingredient has no deleterious effects on the specified properties. Cementitious materials and aggregates shall be measured by mass (or by volume). Volumetric measurement shall be calibrated by mass. Fibres are measured by mass. Admixtures are measured by mass or volume. Shortcrete ingredients shall be thoroughly blended at a central location. Mixer performance tests shall be performed to establish the mixing time suitable for uniformity of mixing. Type FA and CA shortcrete shall meet the requirements when mixed and tested in accordance with the procedure for mixing and testing. Grade GU shortcrete shall meet the general requirements for type FA or type CA shortcrete. Grade SR shortcrete shall have sulfate resistance. Grade LP shortcrete shall have a very low chloride penetrability rating. Grade FR shotcrete shall have fiber reinforcement with a minimum average residual (Grade FR Class I) and flexural strength (Grade FR Class II) when tested. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers laboratory performance standards for pre-blended, dry, packaged, combined materials for use in wet or dry shotcrete applications that are delivered to a purchaser with the ingredients uniformly mixed. The use of supplemental materials, placement, curing, or protection of the shotcrete after delivery to the purchaser is not addressed by this specification. 1.2 The values stated in either SI units or inch-pound units shall be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The following safety hazards caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards C78 Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) C150 Specification for Portland Cement C387/C387M Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar C595 Specification for Blended Hydraulic Cements C1012 Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution C1140 Practice for Preparing and Testing Specimens from Shotcrete Test Panels C1157 Performance Specification for Hydraulic Cement C1202 Test Method for Electrical Indication of Concretes Ability to Resist Chloride Ion Penetration C1385/C1385M Practice for Sampling Materials for Shotcrete C1399 Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete C1436 Specification for Materials for Shotcrete National Institute of Standards and Technology Handbook44 Specifications, Tolerances, and Other Technical Requirements for Commercial Weighing Devices Available from National Institute of Standards and Technology (NIST), Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402Keywords average residual strength; compressive strength; dry mix shotcrete; flexural strength; packaged shotcrete materials; pre-blended shotcrete materials; shotcrete; wet mix shotcrete; ICS Code ICS Number Code 91.100.30 (Concrete and concrete products) DOI: 10.1520/C1480_C1480M-07R12 ASTM International is a member of CrossRef. ASTM C1480 / C1480MThis book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|