|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-A1059 2013ASTM A1059 / A1059M - 08(2013)Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other ProductsActive Standard ASTM A1059 / A1059M | Developed by Subcommittee: A05.13 Book of Standards Volume: 01.06 ASTM A1059 / A1059M1. Scope 1.1 This specification covers the general requirements for protective zinc coatings (hereinafter referred to as the coatings) to be applied by the thermo-diffusion coating (TDC) method, to various products made of carbon steel, including low and high tensile parts as well as of wrought iron, sintered iron steel-powder and various steel and stainless alloys. TDC is carried out by immersing the parts in a zinc alloy powder at elevated temperature for a period of time, causing a metallurgical diffusion process of zinc and iron. Further processing may be added, such as, passivation, topcoat application, paint application, etc. 1.2 This specification is applicable to orders in either inch-pound units (as A1059) or in SI units (as A1059M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in inch-pound units, such shall be stated to the applicator when the order is placed. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings A385 Practice for Providing High-Quality Zinc Coatings (Hot-Dip) A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment A902 Terminology Relating to Metallic Coated Steel Products B487 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section D521 Test Methods for Chemical Analysis of Zinc Dust (Metallic Zinc Powder) D6386 Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting E376 Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current (Electromagnetic) Testing Methods F1789 Terminology for F16 Mechanical Fasteners F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners F2674 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners [Metric] Keywords coatings, zinc; fasteners, zinc coated; iron products, zinc coated; steel hardware, zinc coated; steel products, metallic coated; zinc coatings, steel products; ICS Code ICS Number Code 25.220.40 (Metallic coatings) DOI: 10.1520/A1059_A1059M-08R13 ASTM International is a member of CrossRef. ASTM A1059 / A1059MThis book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|